Rane MQ 302S Manual

Rane Blander MQ 302S

Læs gratis den danske manual til Rane MQ 302S (9 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Rane MQ 302S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

Manual-1

OPERATORS MANUAL

QUICK START

If this is your first equalizer, please do yourself and

your speakers a favor and read at least the first five pages.

“An ounce of prevention...,” and all that.

The MQ 302S is a stereo equalizer, so adjusting any

slider affects both channels simultaneously. Begin by

setting all sliders to their center detent (0 dB), and the

INPUT LEVEL to its center detent (0 dB). Try to make

more cuts than boosts. After equalizing, use the EQ switch

to compare equalized and non-equalized signal. While EQ

is switched to ACTIVE (out), adjust the INPUT LEVEL

to the same level as when EQ is switched to BYPASS

(in).

You may use either the XLR or ¼" connectors for

Inputs or Outputs. Connect only one INPUT type per

channel. The XLR and ¼" TRS inputs do not sum. You

may, however, use both types of OUTPUTS simulta-

neously if desired.

WEAR PARTS: This product contains no wear parts.

MQ 302S

STEREO GRAPHIC EQUALIZER

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

To reduce the risk of electrical shock, do not open the unit. No user

serviceable parts inside. Refer servicing to qualied service personnel.

e symbols shown below are internationally accepted symbols that warn

of potential hazards with electrical products.

is symbol indicates that a dangerous voltage

constituting a risk of electric shock is present within

this unit.

is symbol indicates that there are important

operating and maintenance instructions in the

literature accompanying this unit.

WARNING

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, registers, stoves, or other apparatus (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A ground-

ing-type plug has two blades and a third grounding prong. e wide blade or third prong is provided for your safety. If the provided plug does not

t into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord and plug from being walked on or pinched particularly at plugs, convenience receptacles, and the point where it exits from

the apparatus.

11. Only use attachments and accessories specied by Rane.

12. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply

cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

15. e plug on the power cord is the AC mains disconnect device and must remain readily operable. To completely disconnect this apparatus from

the AC mains, disconnect the power supply cord plug from the AC receptacle.

16. is apparatus shall be connected to a mains socket outlet with a protective earthing connection.

17. When permanently connected, an all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated in the electri-

cal installation of the building.

18. If rackmounting, provide adequate ventilation. Equipment may be located above or below this apparatus, but some equipment (like large power

ampliers) may cause an unacceptable amount of hum or may generate too much heat and degrade the performance of this apparatus.

19. is apparatus may be installed in an industry standard equipment rack. Use screws through all mounting holes to provide the best support.

WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture. Apparatus shall not be exposed to dripping

or splashing and no objects lled with liquids, such as vases, shall be placed on the apparatus.

NOTE: is equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. ese

limits are designed to provide reasonable protection against harmful interference in a residential installation. is equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.