Rane HC 4 Manual

Rane Blander HC 4

Læs gratis den danske manual til Rane HC 4 (4 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Rane HC 4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Manual-1

OPERATORS MANUAL

QUICK START

Conect the output from any stereo source such as a mixer or tape deck, and plug the left and right inputs into the

respective INPUT jacks. The Inputs accept balanced or unbalanced sources. Just plug them in. This source is now routed to

each of the four Outputs.

For a single mono source feeding all headphones, connect it to either one of the INPUT jacks and engage the STEREO/

MONO switch. Set the CHANNEL LEVEL controls for individual headphone levels.

Never connect anything except a Rane power supply to the thing that looks like a telephone jack on the rear of the

unit. This is an AC input and requires special attention if you do not have a power supply exactly like the one originally

packed with your unit. See the full explanation of the power supply requirements elsewhere in this manual.

WEAR PARTS: This product contains no wear parts.

HC 4

HEADPHONE AMPLIFIER

Manual-2

STEREO/MONO switch

Converts the INPUTS from stereo to

mono so that a single input cable drives

both sides of the headphones. In some

instances a STEREO program may be

confusing for live monitoring purposes,

and switching to MONO improves

intelligibility by summing the Left and

Right signals.

OVERLOAD indicators

The red LEDs light when the input

signal exceeds the HC 4’s output

capability (3 dB below maximum).

Occasional flickering is acceptable.The

overload point automatically varies with

the headphones used.

Chassis ground point

A screw is supplied for chassis

grounding purposes. This unit comes

with an outboard power supply which

does not ground the chassis through the

line cord. The HC 4 can be grounded

either to another chassis which is earth

grounded, or directly to the grounding

screw on an AC outlet cover by means

of a wire connected to this chassis

grounding screw.

Remote POWER supply input

The unit is supplied from the factory

with a Model RS 1 remote power supply

suitable for connection to this input

jack. The power requirements of the

unit call for an 18 volt AC center-tapped

transformer only. This is not a tele-

phone jack. Never use a power supply

with your unit other than the one

supplied or a replacement approved

by Rane Corporation. Using any other

type of supply may damage the unit and

void the warranty.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	HC 4

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane HC 4 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

Blander Manualer

Nyeste Blander Manualer

Glemm MMX 54ZM Manual

21 Juni 2025

Roland M-5000 Manual

20 Juni 2025

DNA HLC 10 MK2 Manual

17 Juni 2025

16 Juni 2025

16 Juni 2025

16 Juni 2025

15 Juni 2025

13 Juni 2025

13 Juni 2025

NutriBullet Ultra Plus+ Manual

12 Juni 2025