Rane ECM 64e Manual

Rane Blander ECM 64e

Læs gratis den danske manual til Rane ECM 64e (26 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Rane ECM 64e, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/26

Manual-1

OPERATORS MANUAL ECM 64e

CONFERENCE SYSTEM

Quick Start

The ECM 64e is a very versatile product with many applications. This section will help you with basic setup, then use the

Contents below to find the detail you need for your specific application.

Although the ECM 64e or ECM 64eAD are configured to operate ‘out of the box’, to get the best performance please

review this manual for proper configuration and alignment (see page Manual-12). The ECM 64eAD includes both the DH 1e

Digital Hybrid and the ECA 2 Echo Canceller. If you are using the ECM 64e without these options, hardware and software

references to them in this manual will not apply.

The ECM 64e is configured using RaneWare® software. To become familiar with the ECM 64e signal routing, you can

load and run RaneWare on a PC before connecting the ECM 64e. In RaneWare, click on the Device button and select

Offline ECM 64e. This creates a virtual product which is fully operational, even saving and recalling system files as if it

were a real unit. Press F1 at any time to get help, then get information about any feature by clicking on it. Here at Rane, we

spend a lot of time putting together very informative help files, so please use them — you'll help us feel appreciated!

Before connecting any cables to the ECM 64e, unplug the RS 3 power supply and turn the amplifier(s) down or off until

all connections are complete. Connect balanced audio INPUTS and OUTPUTS to the handy Euroblock connectors.

Connect the RW 232 INPUT jack to a serial (COM) port on a PC-compatible computer using a standard 9-pin RS-232

cable (a short one is supplied with the unit, intended to connect between multiple RW 232 units in a rack). The cable or

adaptor must not be a null-modem type. If this unit is to be used by itself, set the RW 232 DEVICE ADDRESS switch to

‘1’ by setting all switches off (down), except switch one (labeled ‘1’ on the chassis, the right-most switch). If there is more

than one unit, refer to “Setting the Device Address” on page Manual-7 to set a unique number.

After all connections are made, connect the RS 3 remote power supply and line cord. CAUTION: don’t connect anything

but an approved Rane power supply. If the RS 3 and the ECM 64e are getting power, the yellow POWER indicator lights.

Start your computer running Windows®, and launch RaneWare. Select System Setup from the System menu. Be

sure to select the COM port which is physically connected to the ECM 64e and RS-232 under Connection, and click OK.

Now, choose Select from the Device menu. Click on Poll, and Devices Found displays the number of units. Click the

Stop button. Select the unit listed in the Device Selection window and click OK. If no unit was found, refer to the

“Troubleshooting” section on page Manual-13.

Several clues indicate communication between the computer and the ECM 64e. The yellow COM (communications)

indicator should flash periodically. The Memory numbers (1-16) near the top of the RaneWare screen should be black

rather than gray.

Most echo problems are caused by improper microphone placement and gain. To achieve good acoustic echo canceller

performance, setup is critical. Follow the “Alignment Procedure” on page Manual-12.

Table of Contents

Hardware

ECM 64e – Front Panel Description ............. 2

ECM 64e – Rear Panel Description .............. 3

Typical ECM 64eAD Installation .................... 4

Site Survey ........................................................... 6

ECM Connection ................................................ 6

Memory Recall Port .......................................... 7

Software Operation .............................................. 8

Overview ............................................................... 8

System Requirements ...................................... 8

Software Installation ........................................ 8

Device Selection ................................................ 9

Memory & Security ............................................ 9

Saving & Printing ............................................... 9

Inputs ................................................................... 10

Outputs ............................................................... 10

Acoustic Echo Canceller ................................ 10

Digital Hybrid .................................................... 11

Alignment Procedure ......................................... 12

Troubleshooting .................................................. 12

ECM 64e Options ................................................ 13

Advanced Application ........................................ 14

Device Control Language ................................. 16

RW 232 Communications Interface ............... 24

Example Packet Expansion Code .................. 25

Compliance Notices ........................................... 26

WEAR PARTS: This product contains no wear parts.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	ECM 64e

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane ECM 64e stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

24 Juni 2025

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

Blander Manualer

Nyeste Blander Manualer

Audac M2 Manual

16 Oktober 2025

Proel ATMP480Z6XL Manual

14 Oktober 2025

TOA M-124FX-EB Manual

10 Oktober 2025

Audiophony MYA8C Manual

6 Oktober 2025

Audiophony Digital-3 Manual

6 Oktober 2025

Audiophony MYA5D Manual

5 Oktober 2025

Proel MQ16USB Manual

4 Oktober 2025

Rolls Mini-Mix VI MX28 Manual

3 Oktober 2025

Rolls RM65B Manual

3 Oktober 2025

Rolls PM60 Manual

3 Oktober 2025