Rane FPS 28 Manual

Rane Blander FPS 28

Læs gratis den danske manual til Rane FPS 28 (4 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Rane FPS 28, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

OPERATING / SERVICE MANUAL

FPS 28

QUICK START

This section has been provided as a convenience for those without enough patience to read the

entire manual. If you are experienced with this unit or other Rane Flex modules, these few words

should help refresh your memory.

Inputs may be mic or line level. The choice between the two is made by setting the pushbuttons

on the rear of the unit near each input. Balanced inputs use pin 2 as hot, pin 3 as return and case

as shield ground. Unbalanced inputs should be connected to pin 2 for hot and pin 1, signal

ground, for return. The 1/4" expand outputs are to be used for daisy-chaining the inputs to

another destination. These are tip ring sleeve connectors where the tip is hot, ring is return and

sleeve is ground. Alternatively these may be used as inputs.

The outputs are 1/4" tip ring sleeve jacks where the tip is A output, ring is B output and sleeve is

ground. Signal for these outputs may be sourced either before or after the A and B MASTER

level controls. The switches which determine this are located within the confines of the unit’s

covers. All FPS 28s are shipped from the factory with the switches in the POST fader position.

Once inputs and outputs are satisfactorily connected, set the input gains as high as possible

without causing the A and B overload indicators to illuminate steadily with very high input levels.

If 1 x 8 splitter operation is required, only one input is used and the STEREO / MONO switch should

be in the MONO position. If 1 x 4 stereo operation is chosen the switch should be in the opposite

position.

NEVER CONNECT ANYTHING EXCEPT AN APPROVED RANE POWER SUPPLY TO

THE RED THING THAT LOOKS LIKE A TELEPHONE JACK ON THE REAR OF THE FPS

28. This is an AC input and requires special attention if you do not have a power supply EXACT-

LY like the one that was originally packed with your unit. See the full explanation of the power

supply requirements elsewhere in this manual.

SYS TE M CON NE CT I ON

When connecting the FPS 28 to other components in your system for the first time, LEAVE

THE POWER SUPPLY FOR LAST. This gives you a chance to make mistakes and correct them

without damage to your fragile speakers, ears and nerves.

INPUTS. The two inputs on the FPS 28 are balanced. They may also be used in an unbalanced

configuration. Use only shielded cable for inputs. This wire should always be two-conductor plus

shield, even for unbalanced operation. Balanced inputs should be connected to both the “+” pin

2 and “–” pin 3 for signal hot and return. The shield should be tied to case ground. A neutral “pin

1” ground is not necessary (except when using phantom power). For unbalanced use, connect the

hot side of the input cable to pin 2 and signal return to pin 1. It is never necessary on any Rane

Flex module to ground the pin 3 input in the unbalanced mode. It won’t, however, hurt anything if

you do. If the input is coming from another piece of equipment in the signal path, connect the

shield only at the receiving end to help prevent ground induced hum. If a microphone is being

connected to the unit, the shield may be connected to the case of the mic as well as to the ground

terminal on the unit.

OUTPUTS. The FPS 28’s outputs are unbalanced. Channel A is present on the tip of these jacks,

channel B is the ring. Use two conductor shielded cable for this purpose with the shield con-

nected to the sleeve. Shield must be connected on both ends of the cable.

7. POWER INDICATOR. When this yellow LED is illuminated, the foregoing informa-

tion should be correct. If darkness is present at this location, most or all of the above will

be inoperative.

6. OUTPUT LEVEL CONTROLS. Each pair of output controls sets the individual chan-

nel output levels. The inner knob is for channel A, the outer is channel B.

5. STEREO/MONO SWITCH. To make one of the inputs on the FPS 28 available to all

eight outputs, this switch needs to be in the MONO position. In the STEREO mode, Input

A drives bus A only; Input B connects to bus B only.

4. MASTER A AND B LEVEL CONTROLS. These concentric controls set the level to

each of the buses. Output levels may be selected via the four pairs of controls connected to

the output sections. This is true, however, only if the internal PRE/POST switches are in

the POST position (as shipped).

In the PRE position, the Master Level Control is bypassed for that respective output

and only the Input Gain Control and the Output Level Control have any effect on an in-

dividual output.

3. PHANTOM POWER SWITCH. In the ON position, 15VDC phantom power will be

present on both 3-pin inputs on the rear of the module.

2. A AND B OVERLOAD INDICATORS. These red LEDs illuminate whenever the com-

bination of input level and input gain adjustment cause the input amplifiers to reach or ex-

ceed a level equal to 4dB below clipping.

1. INPUT LEVEL CONTROLS. These concentric level controls set the level of each

input to be routed to the channel A bus and the channel B bus. The inner knob controls

the level to be sent to bus A, the outer knob controls the signal applied to bus B. Rotating

the knobs upward together from the “0” position creates a “pan centered” effect. Leaving

one off and increasing the other emulates a full pan to one bus or the other.

FRO NT P ANEL DE S CRI PTIO N

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	FPS 28

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane FPS 28 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

Rane DA 216 Manual

20 Juni 2025

Rane RA 27 Manual

20 Juni 2025

Rane GE 30 Manual

20 Juni 2025

Rane Empath Mixer Manual

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

Blander Manualer

Nyeste Blander Manualer

DNA HLC 10 MK2 Manual

17 Juni 2025

16 Juni 2025

16 Juni 2025

16 Juni 2025

15 Juni 2025

13 Juni 2025

13 Juni 2025

NutriBullet Ultra Plus+ Manual

12 Juni 2025

DNA CM8-DSP Manual

9 Juni 2025

DNA HLC 14 MK2 Manual

9 Juni 2025