Rane FVL 22 Manual

Rane Blander FVL 22

Læs gratis den danske manual til Rane FVL 22 (4 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Rane FVL 22, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

OPERATING / SERVICE MANUAL FVL 22

REMOTE VCA / LIMITER

QUICK START

Welcome to the section for all too busy to actually read the manual. We provide this quick

start as a service to our best customers (the ones who buy the product.) Let’s get started…

There are two ways to connect audio to the FVL 22, #6 terminal strips or Patch I/O points. To

use the terminals, attach the balanced lines to the “+”, “–”, and SHIELD GROUND terminals.

To run the FVL 22 unbalanced, attach the positive lead to the “+” terminal and leave the “–”

terminal open. To use the FVL 22 as an external level control/limiter for a mixer or other device

with tip = send, ring = return insert points, simple use the PATCH I/O ¼" TRS jack. Note:

PATCH I/O is an unbalanced signal. Use two conductor cable with shield.

Install your remote control device (5k to 100k linear taper potentiometer, voltage ramp, or

switch) and run two or three wires to the FVL 22. If you are using an external voltage, run one

wire per Channel to the V1 terminal for Channel 1, V2 for Channel 2, and a ground wire to

COMMON GND. To use the provided 10VDC reference, connect a second wire from VREFl or

VREF2 to your pot or switch. Refer to the wiring diagrams on the back page of this manual.

The VCA’s in the FVL 22 provide maximum attenuation of the signal level when a given

voltage is detected between Vl or V2 and COMMON GND. Reducing this voltage with a pot,

ramp, or switch increases the audio signal level. (0 volts or open = VCA full on.)

To calibrate: set the remote pot, ramp or switch to it’s maximum voltage. Adjust the VOLT-

AGE CALIBRATION control until the green CAL indicator is lit.

Rotate the LIMITER threshold control to the level you never wish to exceed at the output.

The AUTO-SLAVE switch position locks the limiter control circuitry for stereo applications,

limiting both Channels equally when either Channel goes into limit.

Upon completion of the setup procedures, use the supplied hole plugs to prevent unautho-

rized adjustments.

Never connect anything except an approved Rane AC Power supply to the thing that looks

like a red telephone jack on the rear of the FVL 22. This is an AC power input and requires

special attention if you do not have a power supply exactly like the one originally packed with

your unit. Rane models FRS 8, RAP 10 or VC 18 power supplies are acceptable as well. Please

see the full explanation of power supply requirements elsewhere in this manual.

SYSTEM CONNECTION

When connecting the FVL 22 to other components for the

first time, leave the power supply for last. This allows for

mistakes to be identified by visual inspection and corrected

before power is applied and it becomes too late.

INPUTS and OUTPUTS on the FVL 22 are connected

via terminal strips or the PATCH I/O jack. Using the termi-

nals, attach the balanced lines to the “+”, “–”, and SHIELD

GROUND terminals. To run the FVL 22 unbalanced, attach

the positive lead to the “+” terminal and leave the “–”

terminal open. To use the FVL 22 as an external processor for

a mixer of other device with tip = send, ring = return insert

points, use the PATCH I/O ¼" TRS jack with a two conductor

shielded cable (the PATCH I/O is unbalanced).

EXTERNAL VCA CONTROL . The VCA’s in the FVL

22 provide maximum attenuation of the signal level when a

voltage is detected between V1 and V2 and COMMON GND.

Reducing this voltage with a pot, voltage ramp, or switch

increases the audio signal level. (0 volts or open = full VCA

on.) This voltage is provided by the VREF terminal on the

FVL 22 or derived by existing voltage sources at the remote

device location. Refer to the wiring diagrams on the last page

of this manual.

POWERING UP. A good visual inspection often elimi-

nates disasters before applying power. It cannot be overstated

how important it is to use the correct power supply with this

and all Flex products. The RS 1 single AC power supply

(included with each module) as well as the Rane FRS 8, RAP

10 and VC 18 power supplies are the only supplies certain to

work properly with the unit. If another supply is considered, it

must be an AC supply. It must have an 18 to 24 volt center-

tapped output and be wired to a 6-in mod connector in

accordance with the requirements of the Rane standard.

FRONT PANEL DESCRIPTION

1. LOW CALIBRATION LED. The VCA’s in the FVL 22 attenuate the

most with the highest voltage across V1 and COMMON GND. Setting

the remote pot, ramp or switch to provide its highest voltage readies the

FVL 22 for calibration. During calibration, if this LED is on, adjust the

VOLTAGE CALIBRATION control clockwise, until the CAL indicator

comes on.

2. CAL LED. This LED illuminates when the maximum voltage is present

between V1 and COMMON GND and the calibration is just right.

3. HIGH CALIBRATION LED. During calibration, if this LED is on,

adjust VOLTAGE CALIBRATION counterclockwise, until the CAL

indicator comes on.

4. VOLTAGE CALIBRATION ADJUST. Use this screwdriver-adjust

control to set the VCA circuitry calibration when the external voltage at

V1 is set to its maximum level.

5. LIMIT THRESHOLD LED. When this LED illuminates, the preset

level threshold of the limiter has been exceeded.

6. LIMITER ADJUST. Rotate this screwdriver-adjust control to calibrate

the point at which the output limits. The inner ring of numbers show the

angle to rotate this control for balanced operation, the outer ring for

unbalanced output levels.

7. AUTO-SLAVE SWITCH. In the INDEPENDEDENT position, each

Limiter Channel operates separately. In the AUTO-SLAVE position,

both Channels attenuate the same amount when either one exceeds its

threshold.

8. POWER INDICATOR. Indicates the power on condition of the FVL 22.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	FVL 22

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane FVL 22 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

24 Juni 2025

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

Blander Manualer

Nyeste Blander Manualer

Ibiza Sound MX401 Manual

14 September 2025

Mackie 1642VLZ4 Manual

14 September 2025

Mackie ProFX10v3+ Manual

14 September 2025

Mackie Master Fader Control App Manual

14 September 2025

Mackie DL32S Manual

14 September 2025

Mackie 1402VLZ4 Manual

14 September 2025

Mackie Onyx 12 Manual

14 September 2025

Mackie ProFX12v3 Manual

14 September 2025

Mackie 1604VLZ4 Manual

14 September 2025

Mackie Pro FX30 v3 Manual

14 September 2025