Rane GE 130 Manual

Rane Blander GE 130

Læs gratis den danske manual til Rane GE 130 (4 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Rane GE 130, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Manual-1

OPERATORS MANUAL GE 130

GRAPHIC EQUALIZER

GE 130 CONNECTION

When first connecting the GE 130 to other components,

leave the power supply for last. This gives you a chance to

make mistakes and correct them without damaging your

fragile speakers, ears and nerves.

INPUTS

Both XLR and Euroblock Inputs are wired in parallel and

are actively balanced. Each works equally well. Choose

strictly from a required hardware point-of-view, there will be

no performance trade-offs. The wiring convention adheres to

American, British and International standards of pin 2 (+) hot,

pin 3 (–) return, and pin 1 shield. Unbalanced operation

involves using only pin 2 or “+” as signal, and pin 1 as shield

or ground. It is not necessary to short any inputs to ground—

it doesn’t hurt, it’s just not necessary. Use pin 1, or the shell,

for shield ground.

QUICK START

So tell me honestly, do you actually read the manuals or do you just want to connect the thing and go? If you are one

of the “gotta go now” crowd please read this short section. Even if you read slowly so as to savor every syllable, it only

takes a couple of minutes and may save more of your valuable time later. The rest of this manual is dedicated to those who

really want to know all the nitty-gritty details.

Wait a minute before plugging in the power supply. Hopefully the equipment to and from the GE 130 is balanced, with

pin 2 “hot.” From the line level output preceding the GE 130, connect a XLR male connector to the INPUT jack on the rear

of the GE 130. Connect a female XLR connector to the OUTPUT jack on the rear of the GE 130, to the next line level

device in the signal chain.

Now plug in the power supply. The yellow POWER LED should illuminate, and if you have an audio source working

and the rest of the signal chain completed, you will hear audio. With sliders centered and the LEVEL control at “7”

(corresponds to about 2 o’clock), depress the BYPASS switch. If any difference in level exists, adjust the LEVEL control

so the same volume exists whether BYPASS is in or out. You now have an expensive jumper wire. Fully utilizing the

capabilities of the GE 130 requires moving some of the sliders, but you already knew that. To make best use of the GE 130,

use some sort of an analyzer to adjust the sliders properly.

Never connect anything except an RS 1 or other approved Rane AC power supply to the thing that looks like a

telephone jack on the rear of the unit. This is an AC supply and requires some special attention if you do not have an

operational power supply exactly like the one that was originally packed with your unit.

OUTPUTS

The Outputs mimic the Inputs. Balanced output requires

using pin 2 or “+”, and pin 3 for the signal ground. It does not

require pin 1 or shield. The signal exists differentially

between the two balanced leads; ground is not involved. For

hum-free systems ground is used only for shielding.

SIGNAL LEVELS

Signal levels from -10 dBV to +4 dBu are considered

normal and within range (at least 20 dB of headroom exists

above these levels). Do not directly connect microphones

into the GE 130. These require a mic preamp.

WEAR PARTS: This product contains no wear parts.

Manual-2

FRONT PANEL DESCRIPTION

햲 POWER indicator illuminates whenever the appropriate power supply is connected to the unit with the correct line

voltage source.

햳 BYPASS switch and indicator: When the bypass switch is in the in position the red BYPASS LED illuminates and the unit

is in the BYPASS mode. In this mode the audio signal is routed directly from the INPUT to the OUTPUT jacks without

passing through any active circuitry (often referred to as hard-wire bypass). Use this switch to compare equalized and

unequalized material. In the event of power failure, the GE 130 automatically goes into BYPASS.

햴 OVERLOAD indicator illuminates if any section of the GE 130 is within 3 dB of clipping. Occasional blinking of this

LED is acceptable, but if it remains on more than intermittently, turn down either the equalizer’s LEVEL control or reduce

the output level of the preceding component to avoid distortion.

햵 LEVEL control sets the Level of the signal coming into the GE 130. Turn this control down if the OVERLOAD LED

lights up steadily (meaning too strong an Input signal). Since actual unity gain depends on varying slider settings (which is

why we have not marked a unity gain position on the front panel), use the BYPASS switch to determine the exact unity gain

position of this LEVEL control by comparing EQ and BYPASS loudness.

햶 Filter Level slide controls: Each of these sliders control the output level of each of the 30 bandpass filters.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	GE 130

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane GE 130 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

24 Juni 2025

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

Blander Manualer

Nyeste Blander Manualer

Ibiza Sound MX401 Manual

14 September 2025

Mackie 1642VLZ4 Manual

14 September 2025

Mackie ProFX10v3+ Manual

14 September 2025

Mackie Master Fader Control App Manual

14 September 2025

Mackie DL32S Manual

14 September 2025

Mackie 1402VLZ4 Manual

14 September 2025

Mackie Onyx 12 Manual

14 September 2025

Mackie ProFX12v3 Manual

14 September 2025

Mackie 1604VLZ4 Manual

14 September 2025

Mackie Pro FX30 v3 Manual

14 September 2025