Rane GE 30 Manual

Rane Blander GE 30

Læs gratis den danske manual til Rane GE 30 (4 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Rane GE 30, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Manual-1

GE 30

GRAPHIC EQUALIZER

OPERATORS MANUAL

GE 30 CONNECTION

When connecting the GE 30 to other components in your

system for the ﬁrst time, . is will leave the power supply for last

give you a chance to make mistakes and correct them before any

damage is done.

INPUTS on the GE 30 are balanced. ey may be con-

nected for either balanced or unbalanced operation. is product

oﬀers the choice between going in and out of it using either the

3-pin connectors or the handsome black #6 terminal strips with

the ﬁnely plated screws. We will describe here the use of the 3-

pin connectors. e terminal strips are connected in parallel and

are used in the same way. Only the names have been changed.

Pin 2 is hot “+”, pin 3 is return “–”, and pin 1 is chassis ground.

Balanced inputs require the use of pins 2 and 3. Pin 1 is unnec-

essary unless you are using it for shield ground. For unbalanced

operation, pins 1 and 3 must be shorted together to prevent 6 dB

of gain reduction. Drive pin 2 as hot and the combination of 1

and 3 as ground.

OUTPUTS are balanced as well and follow the same con-

vention as the inputs. ere are some tricky things to be careful

of at the output. If active balanced operation is your preference,

hot “+” and return “–” should be all that is required. It does

not take three wires to conduct a signal from one unit to the

next. Connect the shield to case or chassis ground. Transformer

balanced outputs are connected in the same manner. Active un-

balanced output requires “+” and ground only. Use pins 2 and 1

respectively. In this mode, do not short pins 1 and 3. If, however,

you are using the transformer coupled mode and are running

unbalanced, short pins 1 and 3 or you will get little or no do

output. In case you haven’t noticed, if you plan on throwing the

selector switch very often it’s a good idea to connect everything

in a balanced conﬁguration.

QUICK START

If you are one of those people who think owner’s manuals are included with a product to help absorb shock and vibration during

shipment, you are a lot like we are. is section is for you. You want to ﬁre up your equalizer without wading through a bunch of

stuﬀ in manuals. Great. Read on. We’ll keep it short.

Set the input control to about . is is approximately unity gain in the LEVEL 6 BOOST/CUT CUT-ONLY mode. (In the

mode the level control should be set to for unity gain.) Your sound system should be set up such that gain or loss is not required in 2

the equalizer(s). Set the switch on the rear for the desired operating mode, EQ MODE CUT-ONLY or BOOST/CUT. e LEDs on

the front illuminate, telling you which mode you are in. Set the switch on the rear for the desired output coupling OUTPUT MODE

mode ( or ). Adjust the and ACTIVE TRANSFORMER COUPLED LOW CUT HIGH CUT FILTER controls on the front for

the desired low and high cut frequencies. Full counterclockwise on the control and full clockwise on the LOW CUT HIGH CUT

control essentially defeats these functions.

If you read only this section, we assume you know how to set up an equalizer. So set the sliders where you want them and you’re

outta here.

Never connect anything except an RS 1 or other approved Rane AC power supply to the thing that looks like a telephone

jack on the rear of the GE 30. is is an AC input and requires some special attention if you do not have an operational power

supply EXACTLY like the one that was originally packed with your unit. See the full explanation of the power supply requirements

elsewhere in this manual.

WEAR PARTS: is product contains no wear parts.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	GE 30

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane GE 30 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

24 Juni 2025

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

Blander Manualer

Nyeste Blander Manualer

Audac M2 Manual

16 Oktober 2025

Proel ATMP480Z6XL Manual

14 Oktober 2025

TOA M-124FX-EB Manual

10 Oktober 2025

Audiophony MYA8C Manual

6 Oktober 2025

Audiophony Digital-3 Manual

6 Oktober 2025

Audiophony MYA5D Manual

5 Oktober 2025

Proel MQ16USB Manual

4 Oktober 2025

Rolls Mini-Mix VI MX28 Manual

3 Oktober 2025

Rolls RM65B Manual

3 Oktober 2025

Rolls PM60 Manual

3 Oktober 2025