Rane MC 22 Manual

Rane Blander MC 22

Læs gratis den danske manual til Rane MC 22 (11 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Rane MC 22, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/11

Manual-1

OPERATORS MANUAL

QUICK START

Shredded, this document makes excellent packing material. In its present form, it makes interesting and useful reading.

If you run out of patience quickly, at least read this part to make sure you don’t exterminate everything within a two mile

radius by doing something wrong.

Attach one or two channels of inputs and outputs to the respective connectors on the rear. This device uses low imped-

ance balanced line drivers. Do not connect the XLR “+” or “–” output pins to ground, as this may cause the power supply

to shut down. For unbalanced use, leave the unused output pin (“+” or “–”) unterminated.

With the RATIO turned all the way down at 1:1, THRESHOLD turned all the way up to 20 dBu, and the LEVEL

controls in their center at 0 dB, you have an expensive patch cord.

While sending a signal to the MC 22, adjust the INPUT LEVEL so the +4 dBu LED lights occasionally, but the OL

LED does not light. Now increase the RATIO to something useful, like 2:1 (with the control set at 2, the Ratio is 2:1; at 5,

it is 5:1.) Adjust the THRESHOLD to the point you want the Compressor to kick in. The GAIN REDUCTION meter

reads the amount of signal compression.

Both Compressors will activate by the source material applied to either Channel if the LINK switch is ON. This is the

preferred setting for stereo program material.

WEAR PARTS: This product contains no wear parts.

MC 22

STEREO COMPRESSOR

Manual-2

INPUT LEVEL control

This controls the overall level. Unity gain is

reached at “0”. With signal applied, set this

control so the +4 dBu LED lights occasion-

ally. If the OL (overload) LED flashes, turn

the INPUT LEVEL control down.

THRESHOLD control

This control sets the point at which the Input

signal level causes the Compressor to

become active. See Figure 1 on page

Manual-4.

COMPRESSOR

ACTIVE/BYPASS switch

This switch compares compressed and non-

compressed signal. There is one for each

Channel. The INPUT LEVEL remains active

regardless of switch position.

LED

This illuminates whenever noise reduction is

active. This automatic downward expander

circuit acts like a gate to keep the system

quiet when no signal is present. When the

input level drops below -55 dBu, downward

expansion occurs at a ratio of 2:1. See

Figure 3 on page Manual-5.

RATIO control

Once the threshold is exceeded, the ratio of

input change to output change is determined

by this control. The compressor has no

effect when set at 1:1. But at 10:1, it takes

a 10 dB input signal increase above the

Threshold to produce a 1 dB increase in

Output Gain. See Figure 2 on page

Manual-4.

GAIN REDUCTION LEDs

These LEDs show the amount of average

signal reduction in dB. This aids in setting

the THRESHOLD and RATIO controls by

showing how much compression is occuring.

CHANNEL 2 OUTPUT

Same as Channel 1 Output.

CHANNEL 2 INPUT

Same as Channel 1 Input.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	MC 22

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane MC 22 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

20 Juni 2025

20 Juni 2025

20 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

Blander Manualer

Nyeste Blander Manualer

DNA HLC 10 MK2 Manual

17 Juni 2025

16 Juni 2025

16 Juni 2025

16 Juni 2025

15 Juni 2025

13 Juni 2025

13 Juni 2025

NutriBullet Ultra Plus+ Manual

12 Juni 2025

DNA CM8-DSP Manual

9 Juni 2025

DNA HLC 14 MK2 Manual

9 Juni 2025