Rane ME 15B Manual

Rane Blander ME 15B

Læs gratis den danske manual til Rane ME 15B (5 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Rane ME 15B, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Manual-1

OPERATORS MANUAL ME 15B

microGRAPHIC EQUALIZER

QUICK START

If this is your first equalizer, please do yourself and your speakers a favor and read the complete manual. “An ounce of

prevention...,” and all that.

You may use either the 3-pin or ¼" TRS connectors for Inputs or Outputs. Hook-up is intuitive. Just follow the

silkscreened instructions on the rear of the unit. Polarity convention is per IEC/ANSI/AES standards of pin 2 positive, pin 3

negative and pin 1 shield. The ME 15B does not invert the signal. Only connect one INPUT type per channel. The 3-pin

and ¼" TRS Inputs do not sum. You may, however, use both types of OUTPUTS simultanesously if desired.

Anyone familiar with other graphic equalizers finds the ME 15B just as familiar. Setting curves is as easy as it is on all

Rane graphics thanks to our innovative constant-Q circuitry. If you feel you want more information on setting up your

curves, please read on.

If you are familiar with equalizers, then hook-up, plug-in, turn-on and go!

ME 15B CONNECTION

When first connecting the ME 15B to other components,

leave the POWER switch off until the very last. This gives

you a chance to make mistakes and correct them without

damaging your fragile speakers, ears and nerves.

INPUTS

Both 3-pin and ¼" TRS Inputs are wired in parallel and

are actively balanced. Each works equally well. Choose

strictly from a required hardware point-of-view, there will be

no performance trade-offs. The wiring convention adheres to

American, British and International standards of pin 2 or tip

being hot, pin 3 or ring being return, and pin 1 or sleeve being

shield. Unbalanced operation involves using only pin 2 or tip

as signal, and pin 1 or sleeve as shield or ground. It is not

necessary to short any inputs to ground—it doesn’t hurt, it’s

just not necessary. Use pin 1, or the shell, for shield ground.

OUTPUTS

The Outputs mimic the Inputs. Balanced output requires

using pin 2 or tip, and pin 3 or ring for the signal. It does not

require pin 1 or shield. The signal exists differentially

between the two balanced leads; ground is not involved. For

hum-free systems ground is used only for shielding.

EXPANDING

Expanding and/or daisychaining the Inputs and Outputs

normally uses the ¼" jacks. Three parallel Input connectors

allows driving a second signal processor or amplifier without

special cabling.

SIGNAL LEVELS

Signal levels from -10 dBV to +4 dBu are considered

normal and within range (at least 20 dB of headroom exists

above these levels). Do not directly connect microphones into

the ME 15B. These require a mic preamp.

Manual-2

FRONT PANEL DESCRIPTION

1. ON switch: As you have astutely surmised by now, this switch powers up the ME15B.

2. Filter level slide controls: Each of these sliders controls the output level of each of the bandpass filters. Center position is

grounded for guaranteed flat response.

3. OVERLOAD indicators: This red LED lights up if any section of the ME 15B is within 3 dB of clipping. Occasional

blinking of these LEDs are acceptable, but if they remains on more than intermittently, turn down either the equalizer’s

LEVEL control(s) or reduce the output level of the preceding component to avoid audible distortion.

4. LEVEL controls: These control the level of signal coming into the ME 15B. Turn this control down if it’s OverLoad LED

lights up steadily (meaning too strong an Input signal). Since actual unity gain depends on varying slider settings (which is

why we have not marked a unity gain position on the front panel), use the BYPASS switch to determine the exact unity gain

position of this LEVEL control by comparing EQ and BYPASS volumes.

5. BYPASS switches: When the red LED is lit, this indicates that the Channel is in the BYPASS mode: signal is routed directly

from the Input to the Output without passing through any active circuitry (often referred to as “hard-wire bypass”). Use this

switch to compare equalized and unequalized material, or to bypass the EQ section in the event of power loss or unit failure.

6. Filter RANGE switches: The gain range of the filter sliders is switchable (as a group) from ±6 dB for high resolution, to

±12 dB for maximum boost/cut capability.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	ME 15B

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane ME 15B stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

24 Juni 2025

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

Blander Manualer

Nyeste Blander Manualer

Ibiza Sound MX401 Manual

14 September 2025

Mackie 1642VLZ4 Manual

14 September 2025

Mackie ProFX10v3+ Manual

14 September 2025

Mackie Master Fader Control App Manual

14 September 2025

Mackie DL32S Manual

14 September 2025

Mackie 1402VLZ4 Manual

14 September 2025

Mackie Onyx 12 Manual

14 September 2025

Mackie ProFX12v3 Manual

14 September 2025

Mackie 1604VLZ4 Manual

14 September 2025

Mackie Pro FX30 v3 Manual

14 September 2025