Rane MH 4 Manual

Rane Blander MH 4

Læs gratis den danske manual til Rane MH 4 (8 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Rane MH 4, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Manual-1

OPERATORS MANUAL

QUICK START

Conect the output from any stereo source such as a mixer or tape deck, and plug the left and right inputs into the

respective INPUT jacks. The Inputs accept balanced or unbalanced sources. Just plug them in. This source is now routed to

each of the four Outputs.

For a single mono source feeding all headphones, connect it to either one of the INPUT jacks and engage the STEREO/

MONO switch. Set the CHANNEL LEVEL controls for individual headphone levels.

Never connect anything except a Rane power supply to the thing that looks like a telephone jack on the rear of the

unit. This is an AC input and requires special attention if you do not have a power supply exactly like the one originally

packed with your unit. See the full explanation of the power supply requirements elsewhere in this manual.

WEAR PARTS: This product contains no wear parts.

MH 4

HEADPHONE AMPLIFIER

Manual-2

STEREO/MONO switch

Converts the INPUTS from stereo to mono so

that a single input cable drives both sides of

the headphones. In some instances a

STEREO program may be confusing for live

monitoring purposes, and switching to MONO

improves intelligibility by summing the Left

and Right signals.

OVERLOAD indicators

The red LEDs light when the input signal

exceeds the MH 4’s output capability (3 dB

below maximum). Occasional flickering is

acceptable.The overload point automatically

varies with the headphones used.

Chassis ground point

A screw is supplied for chassis grounding

purposes. This unit comes with an outboard

power supply which does not ground the

chassis through the line cord. The MH 4 can

be grounded either to another chassis which

is earth grounded, or directly to the

grounding screw on an AC outlet cover by

means of a wire connected to this chassis

grounding screw.

Remote POWER supply input

The unit is supplied from the factory with a

Model RS 1 remote power supply suitable for

connection to this input jack. The power

requirements of the unit call for an 18 volt

AC center-tapped transformer only. This is

not a telephone jack. Never use a

power supply with your unit other than

the one supplied or a replacement

approved by Rane Corporation.

Using any

other type of supply may damage the unit

and void the warranty.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	MH 4

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane MH 4 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

20 Juni 2025

20 Juni 2025

20 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

Blander Manualer

Nyeste Blander Manualer

DNA HLC 10 MK2 Manual

17 Juni 2025

16 Juni 2025

16 Juni 2025

16 Juni 2025

15 Juni 2025

13 Juni 2025

13 Juni 2025

NutriBullet Ultra Plus+ Manual

12 Juni 2025

DNA CM8-DSP Manual

9 Juni 2025

DNA HLC 14 MK2 Manual

9 Juni 2025