Rane MP 2 Manual

Rane Blander MP 2

Læs gratis den danske manual til Rane MP 2 (5 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Rane MP 2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Manual-1

OPERATORS MANUAL MP 2

CLUB MIXER

QUICK START

If you are too excited to read the manual, at least read this page to minimize any potential mistakes (we know you don't

make any). Be sure your amplifier is off while making connections, and every time you turn on your system, apply power to

your amplifier last.

The most common assumption is that the cables you already have will work. Well, let's be sure first. None of your RCA

cables should be longer than 10 feet (3 meters) or you are asking for hum. The MAIN and AUX OUTPUTS are balanced

¼" TRS (tip-ring-sleeve) connectors, allowing you to run long lines if neccessary with properly balanced cables. If you

really have to use unbalanced (tip-sleeve) cables, keep them as short as possible (well under 10 feet [or 3 meters]). If you

are connecting balanced devices (3-conductor) to either Input of the MP 2, or are sending the Output to an unbalanced

equalizer or amplifier, consult the included RaneNote “Sound System Interconnection” for proper wiring.

The MP 2 has 3 sets of Outputs. The HOUSE OUTPUT is set by the front panel HOUSE LEVEL control. The AUX

OUTPUT is set by the rear panel screwdriver adjusted AUX LEVEL control. The TAPE OUTPUT is fixed. All Output

level controls are independent of each other. The only Level controls that affect all Outputs simultaneously are the PGM A

and B LEVEL controls.

If you bring a phono signal into P1 or P2 be sure to keep the PHONO switch in; likewise when connecting a CD player

to this input, be sure the PHONO switch is out.

Start with the HOUSE LEVEL all the way down so you don't scare the neighbors. Start with the Crossfader all the way

to the left (PGM A). Select an INPUT for PGM A and another for PGM B and start playing your sources. Set the EQ

controls to the center. Adjust the LEVEL controls so that the bottom three (-24 -12, , and 0) indicators light up. If the +12

indicator flashes, turn down the LEVEL control. Now slowly turn up the HOUSE LEVEL so you can hear things working.

Moving the Crossfader to the right brings in the source selected on PGM B.

The headphone cue system is simple: The PAN controls the headphone mix between the Program going to the HOUSE

and what is on CUE, determined by the CUE switches.

Never connect anything except a Rane RS 1 to the thing that looks like a red telephone jack on the rear of the

MP 2. This is an AC supply and requires some special attention if you do not have an operational power supply exactly like

the one that came with your unit. Consult the Rane factory for a replacement or substitution.

WEAR PART

This product contains the following wear part subject to the ninety (90) day warranty period described on page Warranty-1:

(1) Active Crossfader #11646.

Manual-2

FRONT PANEL DESCRIPTION

햲 MIC LEVEL control: Adjusts the Level of the MAIN MIC Input.

햳MIC OL (overload) indicator: lights when the maximum mic level has been reached, 3 dB before clipping. If this lights

up, either turn the MIC LEVEL down or stop yelling.

햴 Program INPUT selectors: Provide Input selection between the 2 Phono and 2 Line Inputs for each of the Program A or

Program B channels.

햵Program LOW and HIGH EQ level controls: adjust the equalization for each of the Program Channels. This is not

designed to be the only Equalizer in the system, this is intended to provide EQ between varying program materials. We

recommend an external graphic equalizer for best overall system sound, connected between the MASTER OUTPUTS and

the amplifier.

햶 Program LEVEL controls: set the volume of each Program Input, as you would expect! These controls are pre-Cross-

fader, so both Program Level controls also depend on the Crossfader setting(see 햸).

햷 Program meter: This four-segment meter shows signal presence (at -24), optimum signal level (at around 0), and a

warning to turn down the associated LEVEL control if the +12 indicator lights up.

햸 ACTIVE CROSSFADER: Controls the mix of Program A and B Levels in a logical manner. When the Crossfader is all

the way left, only Program A is heard. When it's all the way right, only Program B is heard. When it's right in the middle,

both Program A and B are mixed together equally. This is an Active Crossfader™ which uses a VCA to deliver an extended

life and reduced travel noise, but to insure trouble-free operation, see Fader Cleaning.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	MP 2

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane MP 2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

19 Juni 2025

Blander Manualer

Nyeste Blander Manualer

DNA HLC 10 MK2 Manual

17 Juni 2025

16 Juni 2025

16 Juni 2025

16 Juni 2025

15 Juni 2025

13 Juni 2025

13 Juni 2025

NutriBullet Ultra Plus+ Manual

12 Juni 2025

DNA CM8-DSP Manual

9 Juni 2025

DNA HLC 14 MK2 Manual

9 Juni 2025