Rane RAP 10 Manual

Rane Blander RAP 10

Læs gratis den danske manual til Rane RAP 10 (1 sider) i kategorien Blander. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Rane RAP 10, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

RAP 10

REMOTE AC POWER SUPPLY

OPERATORS MANUAL

GENERAL INSTRUCTIONS

Using the RAP 10 is as easy as it looks. Connect the red

outputs of the RAP 10 to the red input jacks on the products

to be powered using the supplied 6-wire modular connector

cables. The POWER switch controls all units powered from

the RAP 10. Power is applied immediately upon power switch

closure - there is no time delay power-up sequence.

MOUNTING THE RAP 10

Normally the RAP 10 is mounted below the Rane equip-

ment, and (better) toward the bottom of the rack. (Alterna-

tively, mount the RAP 10 at the very top of the rack, and

leave several blank spaces between it and other units.) This

allows sensitive mic level products to be mounted away from

the RAP 10 hum field. If there are any blank panels, always

locate them between audio equipment (or other hum sensitive

units) and the RAP 10 for the most hum-free performance.

Additionally, create as much ventilation space around the

RAP 10 as possible. This is not critical, it is just good

practice. When fully loaded, the RAP 10 requires unrestricted

airflow for proper cooling.

POWER SUPPLY CABLES

Each RAP 10 is shipped with (10) 6-wire modular plug

power supply cables. Additional power supply cables are

available from the factory or your dealer. Two lengths are

offered, either 24 inches (package of 4), or 6 feet (package of

3). Please specify a length when ordering.

CUSTOMIZING POWER SUPPLY CABLE LENGTHS

Rane makes available a Mod Cable Connector Kit for

customizing cable lengths for each installation. This kit

consists of a modular connector crimping tool (manufactured

by AMP, Inc.), plus (25) 6-pin modular connectors. Cutting

and crimping a new mod connector takes about 60 seconds.

6-wire cable and modular connectors must be used for all

interconnection. Common 4-wire cable and connectors will

not work. Do not substitute 4-wire for 6-wire cable and

connectors.

NOT ENOUGH CURRENT

Each output of the RAP 10 is rated for a continuous

current output of 650 mA. If more than 650 mA is required,

and you have an unused output, the issue of paralleling arises.

Paralleling of outputs is permitted with the RAP 10. A cute

trick that makes this easy is to use a 6-wir e wye-adapter (also

called T-connector, duplex jack, dual modular phone coupler,

etc.). Plug the single male end into the unit to be powered,

and run two 6-wir e cables from the duplex female side into

two channels of the RAP 10. This doubles the available

output current from 650 mA to 1.3 A.

TOO MUCH CURRENT

Sometimes you may be tempted to try and power two

units from one output of the RAP 10. If the total current

demand of both units is less than the 650 mA output current,

this daisychaining (running power out of one unit into

another) temptation becomes unbearable. In general, avoid

daisychaining of power supplie s. Daisychaining of power

only works between units interconnected by fully balanced

technique s. There can be no signal ground connecting

daisychained units. Failure to follow this rule results in hum

due to an unbreakable ground loop caused by the common

power supply path. Life is simpler if you just say no.

RESETTING TIME

The RAP 10 is protected by solid-state current and

temperature sensing devices that reset automatically. This

automatic resetting takes approximately 15 minutes depend-

ing upon the nature of the overload. If power is lost on an

output, disconnect the power cable and wait at least 15

minutes before reconnecting the cabl e. Meanwhile try to find

out why the unit demanded excessive current (Cable short?

Unit failed? Other?).

©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 TEL (425)355-6000 FAX (425)347-7757 WEB http://www.rane.com

CAUTION: THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED PERSONNEL ONLY. TO AVOID ELECTRIC

SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS

UNLESS YOU ARE QUALIFIED TO DO SO. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL.

Produkt Specifikationer

Mærke:	Rane
Kategori:	Blander
Model:	RAP 10

Har du brug for hjælp?

Hvis du har brug for hjælp til Rane RAP 10 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blander Rane Manualer

24 Juni 2025

22 Juni 2025

22 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

21 Juni 2025

Blander Manualer

Nyeste Blander Manualer

Fostex D2424LVmkII Manual

7 December 2025

Icon Platform Nano Manual

6 December 2025

Icon trols Manual

26 November 2025

NutriBullet Ultra 1000 Manual

9 November 2025

Audac M2 Manual

16 Oktober 2025

Proel ATMP480Z6XL Manual

14 Oktober 2025

TOA M-124FX-EB Manual

10 Oktober 2025

Audiophony MYA8C Manual

6 Oktober 2025

Audiophony Digital-3 Manual

6 Oktober 2025

Audiophony MYA5D Manual

5 Oktober 2025