RetroSound PA-02 Manual

RetroSound TV antenne PA-02

Læs gratis den danske manual til RetroSound PA-02 (9 sider) i kategorien TV antenne. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 16 anmeldelser. Har du et spørgsmål om RetroSound PA-02, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

PA02/PA04

Power Antenna

PA02/PA04

Installation Guide

The information enclosed in this installation guide is intended to provide a general outline to assist

you during the process of installation. This guide does not cover every installation possibility,

vehicle, or aspect of the installation process.

Retro Manufacturing, LLC, or its subsidiaries assume no responsibility for proper or improper

installation. Every attempt has been made to make this installation guide as informative as

possible. This guide may be updated from time to time, and specications are subject to change

without notice. Please check our website (help.retromanufacturing.com) for the latest updates.

INSTALLATION

Welcome

Thank you for purchasing a RetroAntenna® Power Antenna. This antenna features fully automatic

operation. This unique antenna allows you to mount the motor separately from the antenna, which

facilitates installation for vehicles with limited space. Please note that this antenna does not work with

antenna systems requiring a switch. Our antenna uses a standard end that is designed to t most

applications. However, some factory radios made after 1988 use a unique connector and may need an

adapter. Contact a local car audio shop for the correct adapter for your application if one is required.

Installing the Antenna

1. Disconnect the battery before you begin the installation. Make sure the area for the antenna has

enough clearance to house the antenna. The PA02 and PA04 antennas require approximately 11 1/2

inches or 29 cm of clearance.

Note: Six mounting bases are provided with the antenna: ve of varying angles and one 0 degree base

preinstalled on the antenna .(see Figure 1)

2. If necessary remove the preinstalled 0 degree base and choose from the other ve to suit your

needs. Select the proper base with the correct angle for your fender (see Figure 1). The ve xed angle

bases require a 7/8 inch or 22 mm hole. The 0 degree base requires a 1inch or 25 mm hole.

Note: If no adequate hole exists, a 1/8 inch or 3 mm pilot hole must be drilled then enlarged with a hole

saw or drill bit to one of the sizes listed above depending on the base you will use.

3. Remove all burrs, paint or dirt from the underside of the hole.

4. Install the new antenna from the underside of the fender and assemble the base above the fender

(see Figure 2). Be sure the metal retainer cup is in place and the adjustable mounting base rests

evenly against the underside of the fender to alleviate any possible damage to the vehicle or antenna.

Align the mast vertically by slightly tightening the antenna mounting nut while adjusting the mast to be

vertical.

5. Secure the bottom of the motor assembly with the supplied metal strap. There are holes in the strap

designed to accommodate various mounting positions. It may be necessary to bend the strap to mount

the motor assembly.

6. Attach the black ground wire to the chassis. Be sure the ground wire is attached to a clean mounting

point for proper operation. If the ground wire is not grounded correctly, the antenna will not function.

7. With the bottom of the antenna motor assembly secured, the mast at the desired angle, and the

adjustable mounting base resting evenly on the underside of the fender, tighten the mounting nut rmly

to secure the antenna assembly. Do not overtighten the nut. Overtightening the nut may strip or break

the mounting threads or damage the contact spring causing improper antenna operation.

8. Attach the drain tube to the bottom of the motor assembly and route it to the outside of the car. Avoid

kinking or bending the drain tube .(see Figure 2)

9. Route the electrical wiring and coaxial cable into the dash area inside the vehicle interior to plug it

into your radio . A 5/8 inch or 16mm hole will be required to route the wire through the (see Figure 3)

inner fender. Avoid routing cables through the engine compartment, and near hot or high current parts.

Antenna cables may pick up interference from high current parts and wiring.

10. Electrical Wiring: For radios with a power antenna wire, connect the green wire from the antenna

to the power antenna wire from the radio (usually blue), then connect the coaxial cable from the antenna

to the radio ( .The red power wire from the antenna can be connected at the fuse block, see Figure 3)

battery or any other constant +12 volt location. If your radio does not have a power antenna wire you

may need to connect the green wire to a switched 12-volt ignition source.

IMPORTANT NOTES

• For optimum operation and reception, you must periodically clean the mast with a damp cloth. Always

clean the mast while it is fully extended. Do not oil or grease the antenna or motor assembly. Doing

so will damage the motor.

• This power antenna is designed to withstand extremely cold temperatures, but under severe icing

conditions the antenna could fail to extend or retract. If this happens, turn the radio on and o󰀨 three or

four times to help free the antenna mast. The antenna motor will not be damaged if the mast does not

extend. A special clutch protects the motor from any possible damage from a frozen mast.

• Always remember to retract the antenna when entering a car wash or low clearance areas.

Produkt Specifikationer

Mærke:	RetroSound
Kategori:	TV antenne
Model:	PA-02

Har du brug for hjælp?

Hvis du har brug for hjælp til RetroSound PA-02 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

TV antenne RetroSound Manualer

RetroSound Retro Antenna PA04 Manual

18 August 2024

RetroSound MC-8207 Manual

9 August 2024

RetroSound PA-03 Manual

9 August 2024

RetroSound PA-01 Manual

9 August 2024

RetroSound PA-02 Manual

9 August 2024

RetroSound RetroAntenna PA04 Manual

9 August 2024

RetroSound HPA-1 Manual

9 August 2024

RetroSound WPA1 Manual

9 August 2024

TV antenne Manualer

Nyeste TV antenne Manualer

Insignia NS-ANT700HA Manual

29 September 2025

President Himalaya WB Manual

25 September 2025

RAMI AV-530 Manual

24 September 2025

One For All 14460 Manual

13 September 2025

Axing TAA 3-00 Manual

10 September 2025

9 September 2025

8 September 2025

8 September 2025

7 September 2025

Schwaiger DTA4000 Manual

31 August 2025