Salus MD22S Manual

Salus Ikke kategoriseret MD22S

Læs gratis den danske manual til Salus MD22S (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 56 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 28.5 anmeldelser. Har du et spørgsmål om Salus MD22S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Instruction Manual

22mm in-line Magnetic Filter

Model: MD22S

www.salus-controls.com

SALUS Controls is a member of the Computime Group

Maintaining a policy of continuous product development SALUS Controls plc reserve the right

to change speciﬁcation, design and materials of products listed in this brochure without prior

notice.

Head Oﬃce:

SALUS Controls

Units 8-10, Northﬁeld Business

Park, Forge Way, Parkgate

Rotherham, S60 1SD

Email: sales@salus-tech.com

www.salus-controls.com

Issued: July 2021

V007

The following instructions are designed to help the engineer to install

and maintain the Magnetic Filter safely and eciently and should be

followed and adhered to at all times. Make sure there is a water-lling

pipeline behind the lter. During maintenance, check whether the lid

seals are worn or damaged. The best practice is to replace the lid seal at

each repair.

The Magnetic Filter is specially designed for central heating systems. It can

remove almost all the harmful black suspended iron oxide particles accumulated

in the central heating system and protect the complete central heating system.

The lter can be installed in a variety of ways, for example: be installed at any

location on the main pipeline. However, it is recommended to be installed

after the last radiator and before the boiler on the primary return pipework for

maximum protection and eciency.

Note: It is important to have adequate access for maintenance and

servicing when determining a suitable installation location.

1 Air vent valve

2 Magnet bar

3 Drain valve

4 Inlet valve

5 Outlet valve

Open vented system

Figure 2

Combination/Sealed system

Figure 1

1. INTRODUCTION

3. STRUCTURE INTRODUCTION

2. MOUNTING RECOMMENDATIONS

Recommended installation location

RETURN

Boiler

RETURN

Boiler

Pump

Header Tank

Vent

Pipe

4. INSTALLATION METHOD

5. MAINTENANCE AND SERVICING

Instruction manual of magnetic lter

1. Cut and remove the section of the pipe according to the product installation length;

2. Install the valves onto the pipework, hand tighten only at rst, then tighten securely the valve to the pipe;

3. Install the lter housing and tighten it;

4. Adjust the Angle and secure the lter;

5. Make sure the valves are open, allow the system to ll, open, and vent the lter through the air vent valve,

close when complete.

1. Close both the isolation valves;

2. Open the drain valve, place a bucket or similar receptacle below ready to collect the debris. Take out the

magnetic bar and store in a safe place;

3. Open the inlet valve to ush out the debris, once all the debris has been removed introduce a suitable

chemical inhibitor into the system, we recommend Salus LX1 inhibitor, ret the magnetic bar;

4. Open the inlet and outlet valve, vent the lter through the air vent valve close when complete.

Check for any leaks;

5. Complete any relevant documentation.

IE: Dates and inhibitor used.

1. The magnetic lter contains powerful magnets, please keep away from all electronic devices, bank cards

and other magnetic devices;

2. The Magnetic Filter contains powerful magnets and should always be used with caution especially for

devices such as pacemakers;

3. The Magnetic Filter is a pressurized device, pressure must be released prior to maintenance;

4. The Magnetic Filter device could be very hot during operation. Please be careful!

* In order to maintain grounding continuity in accordance with the current IEE regulations, appropriate grounding cables should be

installed on the pipe where necessary to bypass the product.

* Please read the product manual carefully before installation and use.

12 3 4

Note: Prior to carrying out any maintenance work, isolate the electrical supply to the boiler allowing

the water to cool down to a safe working temperature.

Note: It is recommended that the magnetic lter is installed and maintained by a competant and

qualied person. Any queries arising from either installation or servicing, contact SALUS Controls at

techsupport@salus-tech.com

Maximum working pressure: 6bar Maximum operating temperature: 95 °C

Flow rate: < 50 l/min Direction of ow: follow the arrow

Please note:

Produkt Specifikationer

Mærke:	Salus
Kategori:	Ikke kategoriseret
Model:	MD22S

Har du brug for hjælp?

Hvis du har brug for hjælp til Salus MD22S stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Salus Manualer

Salus T30NC Manual

25 August 2025

Salus KL08RF 24V Manual

13 August 2025

12 August 2025

12 August 2025

12 August 2025

30 Juli 2025

29 Juli 2025

29 Juli 2025

29 Juli 2025

Salus TRV10RAM Manual

24 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

VIZIO SmartCast M75-E1 Manual

27 August 2025

Prince Castle 740-T4 Manual

27 August 2025

ENTES EMR-53SL Manual

27 August 2025

Minix RIC SJ64-8 Manual

27 August 2025

Milwaukee M18 3019-21PS Manual

27 August 2025

ENTES RGI-12W Manual

27 August 2025

Crestron IV-SAM-VX2-S Manual

27 August 2025

SABO BC-250 PRO Manual

27 August 2025

ENTES DCA-11C Manual

27 August 2025

Russell Hobbs Desire 27140-56 Manual

27 August 2025