Salus PMV38 Manual

Salus Ikke kategoriseret PMV38

Læs gratis den danske manual til Salus PMV38 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 24 anmeldelser. Har du et spørgsmål om Salus PMV38, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

white

blueN

orange

grey

green/yellow

Auxiliary

Switch

230V SL

Isolate grey

3 PORT MOTORISED VALVE

PMV31 (1”) PMV32 (22 mm) PMV34 (3/4”) PMV38 (28 mm)

PRODUCT COMPLIANCE

This product complies with the essential requirements of the following EC Directives:

• Electro-Magnetic Compatibility Directive 2014/30/EU

• Low Voltage Directive 2014/35/EU

• RoHS 2011/65/EU

SAFETY INFORMATION

These instructions are applicable to the SALUS Controls model stated on the front cover of this

manual only, and must not be used with any other make or model.

This accessory must be ﬁtted by a Competent person, and installation must comply with the

guidance provided in the current editions of BS7671 (IEE Wiring Regulations) and Part ‘P’ of the

Building Regulations. Failure to comply with the requirements of these publications could lead

to prosecution.

Always isolate the AC Mains supply before removing or reﬁtting the actuator assembly.

Please leave these instructions with the end user where they should be kept in a safe place for

future reference.

INTRODUCTION

A motorised valve is used to control the ﬂow of water in a central heating system. The motorised

valve can be used for control of both heating and hot water, and it works by controlling the ﬂow

of water from the heating boiler to other parts of the system.

There are two types of motorised valve used in domestic heating systems: two port (also called

zone valves), and three port (also called mid position valves). SALUS Controls oﬀers both types

of valve in a range of standard port sizes.

FEATURES

• Three port option in 1”, 22mm, 3/4” and 28mm sizes

• Removable actuator assembly

• Manual lever and position indicator

• Spring return

• Industry standard wiring

INSTALLATION

Please read the important safety information at the start of this manual before you begin to

install the device.

Before Installation

This valve must only be installed in compatible systems. Before installing, please check that:

• The system pipework has been ﬂushed out to remove any residue.

• There is enough clearance around the valve to allow removal and reﬁtting of the actuator.

• The valve is not installed with the actuator facing down.

• The supply voltage is the same as the voltage indicated on the actuator cover.

• The mains water pressure and the pressure diﬀerentials between valve ports are suitable for

this valve (see Product Speciﬁcation).

Do not restore the mains supply to the system until all associated items are fully installed.

NOTE: All electrical installation work should be carried out by a suitably qualiﬁed Electrician or

other competent person. If you are not sure how to install this motorised valve consult either

with a qualiﬁed electrician, heating engineer or your boiler / heating system supplier for advice

on how to continue.

Electrical Connection

The electrical connections to the motorised valve are made using the pre-wired cable. This

simpliﬁes installation, as no connections need to be made to the actuator itself. The connecting

cable uses industry standard colours, and the connection details are shown below:

MANUAL LEVER

There is a lever on the side of the actuator cover: this lever

allows manual operation of the valve, e.g. for reﬁlling and

draining of the system or if the actuator fails. For two way

valves, the lever allows the valve to be kept open; with three

way valves the lever allows both ports A and B to be open

at the same time.

To manually operate the valve, gently push the lever forward and latch it in the MAN position.

The valve will automatically return to AUTO when the actuator is powered up again.

NOTE: Push the manual lever slowly to prevent damage to the actuator motor and gear system.

The valve should be in manual position to be ﬁtted.

ACTUATOR REMOVAL AND REFITTING

The valve actuator can be removed or reﬁtted without having to disturb the valve installation.

Removal:

1. Remove actuator cover

2. Lock lever in ‘MAN’ position

3 Loosen 2 securing screws

4. Lift actuator from valve body.

Re-tting:

1. Remove actuator cover

2. Lock lever in ‘MAN’ position

3. Turn valve stem to parallel position

as indicated

4. Push actuator onto valve

5. Tighten 2 securing screws

6. Release lever and allow to travel back to ‘AUTO’

Note: Do not attempt to dismantle the actuator assembly as it contains no user serviceable parts

– dismantling or tampering with the actuator assembly will invalidate the product warranty.

MAINTENANCE

The Motorised Valve requires no special maintenance. Periodically, the outer casing can be

wiped clean using a dry cloth (please DO NOT use solvents, polishes, detergents or abrasive

cleaners, as these can damage the Motorised Valve).

There are no user serviceable parts within the unit; any servicing or repairs should only be carried

out by SALUS Controls or their appointed agents.

Should the Motorised Valve fail to function correctly, check:

• The heating system is switched on.

• The lever is not latched in the MANUAL position.

PRODUCT SPECIFICATION

Model: 3 port motorized valve PMV31/32/34/38

Type: Motorised valve designed for domestic heating applications.

Electrical

Switching Voltage: 230V AC / 50Hz

Power Consumption: 6W

Response

Opening: 14 seconds

Closing: 3 seconds

Dierential Pressure

Pipe size 3 Way

22mm 0.8 bar

28mm 0.6 bar

Max Static Pressure: 8.6 bar

Operating Temperatures

Min Fluid Temperature: 5 ºC

Max Fluid Temperature: 88 ºC

Environment

Operating Temperature: -10 ºC to + 60 ºC

Storage Temperature: - 20 ºC to + 65 ºC

Protection class: IP20

AUTO MAN

OPEN

SALUS CONTROLS PLC, SALUS HOUSE, DODWORTH BUSINESS PARK SOUTH,

WHINBY ROAD, DODWORTH, BARNSLEY S75 3SP.

SALES: T: +44 (0) 1226 323961 • E: sales@salus-tech.com

TECHNICAL: T: +44 (0) 1226 323961 • E: tech@salus-tech.com

www.salus-controls.com

white

blueN

orange

grey

green/yellow

Auxiliary

Switch

230V SL

230V

When A is open & B is closed; water ﬂows out from A;

When B is open & A is closed; water ﬂows out from B;

Control wire (Power Supply AC 230V) White - Live. Blue - Neutral

When A is open & B is closed; white 0V, Blue is N;

When B is open & A is closed; white 230V, Blue is N;

Auxiliary switch output (COM, NO) Orange = COM. Grey = NO

Yellow/ Green wire = Earth

When valve is open, orange and grey AUX switch is closed. When valve is closed, orange and grey

AUX switch is open. Yellow/Green wire is for earth.

wired with micro switch

wired without micro switch

Note: For basic diverter

valve applications please

isolate / Disregard the

orange wire. But connect

white and grey together..

22mm 0.8 bar

28mm 0.6 bar

3/4” 0.8 bar

1” 0.6 bar

Produkt Specifikationer

Mærke:	Salus
Kategori:	Ikke kategoriseret
Model:	PMV38

Har du brug for hjælp?

Hvis du har brug for hjælp til Salus PMV38 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Salus Manualer

9 August 2024

29 Juli 2024

23 Juli 2024

22 Juli 2024

20 Juli 2024

18 Juli 2024

8 Juli 2024

19 April 2024

23 Marts 2024

7 December 2023

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Playtive IAN 93699 Manual

16 Juni 2025

Eminence DELTA PRO-12A Manual

16 Juni 2025

Aiphone GT-303HB Manual

16 Juni 2025

Thermaltake Commander FP Manual

16 Juni 2025

Smart365 SM-02-031600 Manual

16 Juni 2025

Playtive IAN 426212 Manual

16 Juni 2025

Playtive IAN 311493 Manual

16 Juni 2025

Playtive IAN 285641 Manual

16 Juni 2025

Playtive IAN 292936 Manual

16 Juni 2025

OmniMount VB42 Manual

16 Juni 2025