Salus RT510BC+ Manual

Salus Termostat RT510BC+

Læs gratis den danske manual til Salus RT510BC+ (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Salus RT510BC+, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

TEST / PAIRING

SELECT

+Hr

SET

iOnce paired please close the

boiler control panel.

The LED will start flashing red.

TEST / PAIRING

+Hr

SELECT SET

RXBC605 Installation

RXBC605 Wiring Terminals

RXBC605

Remove the front panel from the boiler.

Do not remove boiler loop.

Replace the front panel ensuring a good seal is made.

Connect the electrical plug.

Pull out the mechanical timer.

Push fit boiler control into housing.

7Power up the boiler and check the correct operation.

Quick Guide

RT510BC+

Always isolate the AC Mains supply before installing or working on any components

that require 230 VAC 50Hz supply.

RT510BC+ (Thermostat) Button Functions

Introduction

The RT510BC+ thermostat will switch your heating system on or o, as needed, in accordance

with the time and temperature set by you. It can be used with the RXBC605 integral plug-in RF

boiler control. The RF boiler control is a direct replacement for the basic time clock or blanking

plate usually supplied with the boiler. Installing the RF boiler control takes minutes. Once

installed, you will benefit from all the control features of the RT510BC+ thermostat.

868.0-868.6MHz; <13dBm

Safety Information

Use in accordance with the regulations. Indoor use only. Keep your device completely dry. Disconnect

your device before cleaning it with a dry cloth. This accessory must be tted by a competent person, and

installation must comply with the guidance, standards and regulations applicable to the city, country or

state where the product is installed. Failure to comply with the relevant standards could lead to prosecution.

Product Compliance

This product complies with the essential requirements and other relevant provisions of the following EU Directives: EMC

2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of Conformity is

available on www.saluslegal.com

+Hr

SELECT

SET

Key Function

1. Press once to activate Frost Mode

2. Press for 3 seconds in order to activate Holiday Mode

Press once to activate/deactivate Boost function

Press once to enter/exit Permanent Override function

Increase button

Decrease button

Select the clock or programme settings

Press to conrm your settings

1. Press once to enter/exit in Test Mode

2. Press for 3 seconds to enter/exit Pairing Mode

Press the buttons for 3 seconds to enter Installer Mode

Press the buttons for 3 seconds to enter Clock Settings

Box content

Quick Guide 2 x AA Alkaline

Batteries 2 x Fixing Screws

RT510BC+ Desk Stand

Quick Guide

RT510BC

RT510BC+ (Thermostat) Dip Switch Settings

TEST / PAIRING

SELECT

+Hr

SET

TEST / PAIRING

SELECT

+Hr

SET

3 Sec

TEST / PAIRING

+Hr

SELECT SET

Test the Pairing Process

Pairing Process

Once the LED stops flashing, press the

TEST / PAIRING button for 3 sec.

Begin the pairing process

End the pairing process

During test pairing, boiler control should ash conrming pair. If not, please follow

Pairing Process.

When enter test pairing

mode, after a 10 minute

countdown the thermostat

will time out.

Terminal Identier Description

1 N Neutral

2 L Live input (230V AC)

3 Common terminal (volt free)COM

4 N.O. Normally Open

RXBC605 User Controls

RXBC605 Switch Position

LED - It will be on when the thermostat is demanding

heat.

Mode Switch

The AUTO / MANUAL switch allows you to turn on the

Boiler Control manually if required.

SYNC Button - This is used only for pairing the RF

communications.

Press the SYNC button for 3

seconds until LED starts ashing.

The LG+5V is ready to be paired

with your thermostat.

3 Sec

2. MANUAL mode. The user

can also move the switch to the

MANUAL position; when in this

mode, the boiler will be always turned

on and the LED indicator will also

be lit constantly. The manual mode

is only to be used as a temporary

control if problems develop with the

communication from the thermostat.

1. AUTO mode. When the switch

on the Boiler Control is in the AUTO

(normal) position, the Boiler Control

will automatically receive the RF signal

from the transmitter and control the

boiler based on the programming of

the transmitter. 1 2

When the thermostat is operating in

NORMAL mode, if the Boiler Control has

not received a signal from the transmitter

after 1 hour, the Boiler Control will turn

off the boiler, and the LED indicator will

flash constantly (two times every second).

Once the Boiler Control receives a valid

ON or OFF signal, the Boiler Control will

control the heating system accordingly.

SALUS Controls plc

SALUS House

Dodworth Business Park South,

Whinby Road, Dodworth,

Barnsley S75 3SP, UK.

T: +44 (0) 1226 323961

E: sales@salus-tech.com

E: techsupport@salus-tech.com

SALUS Controls is a member of the Computime Group.

Maintaining a policy of continuous product development SALUS Controls plc reserve the right to

change speciﬁcation, design and materials of products listed in this brochure without prior notice.

www.salus-tech.com

Issue Date: February 2018

V007

For PDF Installation guide please go to www.salus-manuals.com

TEST / PAIRING

SELECT

+Hr

SET

3 Sec

PLUS

Internal Temperature

Load Compensation

The DIP Switches can be found on the rear of your thermostat. For all plug-in

boiler receiver applications ensure SW1 is set to RAD.

1 2

NA SPAN

RAD ITLC

Control feature ITLC SPAN

Operation ITLC Internal Temperature

Load Compensation for

improved eciency.

When Span is selected

on DIP switch № 2, the

DIP switch № 1 is not

functional.

+Hr

SELECT SET

TEST / PAIR ING

Setting Time and Date

Programming

Press SET to return to the Main Screen.

+Hr

+Hr +Hr

+Hr

SELECT

SELECT SELECT

SELECT

SET

SET SET

SET

+Hr

SELECT SET

You can create personalized programmes for your controller. You have the option to choose

between a 5-2 days programme or a daily one by using the parameter d04 from Installer mode.

Press UP or DOWN to select Weekday/Weekend/

Day and press SELECT.

Press SET to change your programmes.

+Hr

SELECT SET

Press UP or DOWN to set the minutes and

press SELECT to conrm your option.

Press UP or DOWN to set the temperature and

press SELECT to conrm your option.

Follow the same procedure for the next

set of time.

Review the Setpoint (desired) temperature

Press UP or DOWN to review the setpoint

temperature.

Press UP or DOWN to set the temperature.

Actual room temperature Setpoint (desired) temperature

Boost function

Frost protection

Frost Mode ON.

+Hr

SELECT SET

Press OVERRIDE in order to activate the

mode.

Press UP or DOWN to set the temperature.

+Hr

SELECT SET

Press SET to conrm the changes.

Press +Hr to activate the

Boost function.

Press the FROST button once to activate the

function.

The Override sign will appear on the Main

screen.

Press +Hr to set boost hours and then press

UP or DOWN to set the boost temperature

for your boost period.

+Hr

SELECT SET

Frost Mode OFF.

+Hr

SELECT SET

Holiday Mode

Press the HOLIDAY button for 3 sec. Press the UP or DOWN button to set the

Holiday period.

+Hr

SELECT SET

+Hr

SELECT SET

Press the HOLIDAY button for 3 sec to exit

Holiday Mode.

+Hr

SELECT SET

+Hr

SELECT SET

+Hr

SELECT SET

+Hr

SELECT SET

+Hr

SELECT ETS

SELECT SET

+Hr

SELECT SET

Press UP or DOWN to set the hour and press

SELECT to conrm your option.

+Hr

SELECT SET

+Hr

SELECT SET

+Hr

SELECT SET

+Hr

SELECT SET

Permanent Override

5-2 Days Programme 24h Programme

Weekdays

6 sets of time/channel

Weekends

6 sets of time/channel

Total: 12 settings/week

24h

6 sets of time/channel

Total: 42 settings/week

TEST / PAIR ING TEST / PAIR ING

TEST / PAIR ING

TEST / PAIR ING TEST / PAIR ING

TEST / PAIR ING

TEST / PAIR ING TEST / PAIR ING

TEST / PAIR ING

TEST / PAIR ING TEST / PAIR ING

Continue with the same steps for setting

the Day.

Press the FROST button once to deactivate

the function.

Temporary Override

1 2

+Hr

SELECT SET

Press SET to conrm the changes.

+Hr

SELECT SET

TEST / PAIR ING TEST / PAIR ING

3sec

Press the buttons together for 3 sec.

Press UP or DOWN to select the hour format

and then press SELECT to conrm your

option.

Press UP or DOWN to select the hour

and then press SELECT to conrm your

option.

Press UP or DOWN to select the minutes

and then press SELECT to conrm your

option.

+Hr

SELECT SET

+Hr

SELECT SET

3 Sec3 Sec

+Hr

SELECT SET

+Hr

SELECT SET

TEST / PAIR ING TEST / PAIR ING

After you have done all the changes, please press SET to conrm all your choices

and to return to the Main Screen.

The Frost protection temperature can be reviewed by pressing the UP button

once, but can only be changed in Installer Mode.

You can also exit Holiday Mode by setting the days to zero.

iWhen you want to change the batteries your device will use the internal

memory to backup your settings. You have 30 seconds to change the

batteries before losing your settings.

dxx Function Parameter Default value

d01 Temperature display increments 0.1°C or 0.5°C 0.5°C

d02 Temperature oset +/- 3.0°C 0.0°C

d03 Frost Protection setpoint temperature 5.0°C - 17.0°C 5.0°C

d04 Programmer selection 5/2 or 24 hr (7d) 52d

Installer Mode

+Hr

SELECT SET TEST / PAIR ING

Press the three buttons together

simultaneously for 3 seconds.

+Hr

SELECT SET

3 Sec

GTEST / PAIR IN

3 Sec

Reset function RT510TX+

Remove the batteries without pressing any button. Wait 2 minutes and insert the batteries

again. Your device will be restarted.

NOTE:

If you do not notice the “low battery” symbol displayed on the screen in time, it will

shut down. In this case, after removing the old batteries, it is necessary to wait 5

minutes before inserting the new batteries. Otherwise, it is possible that a condenser

will remain partially discharged and it can prevent the thermostat from restarting.

Produkt Specifikationer

Mærke:	Salus
Kategori:	Termostat
Model:	RT510BC+

Har du brug for hjælp?

Hvis du har brug for hjælp til Salus RT510BC+ stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Salus Manualer

Salus SQ605RF Manual

30 Juli 2025

Salus 091PRO Manual

29 Juli 2025

Salus RT310SPE Manual

24 Juli 2025

Salus RT20 Manual

23 Juli 2025

Salus EL600F Manual

23 Juli 2025

Salus VS35B Manual

23 Juli 2025

Salus 091PRORF Manual

23 Juli 2025

Salus HTRP24 Manual

23 Juli 2025

Salus CB500X Manual

23 Juli 2025

Salus CB500 Manual

23 Juli 2025

Termostat Manualer

Nyeste Termostat Manualer

Honeywell RTH9580WF1005 Manual

14 August 2025

Honeywell YCT30A1003 Manual

14 August 2025

Honeywell RTHL3550D1006 Manual

14 August 2025

Honeywell YCT87K1003 Manual

14 August 2025

Honeywell CT30A1005 Manual

14 August 2025

Honeywell RTH6450D Manual

14 August 2025

Honeywell CT62B1015/U Manual

14 August 2025

Renkforce MH-810HN Manual

14 August 2025

Honeywell RTH2310B1002/A Manual

13 August 2025

Honeywell CT53K1006/E Manual

13 August 2025