Salus RT510WBC+ Manual

Salus Termostat RT510WBC+

Læs gratis den danske manual til Salus RT510WBC+ (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Salus RT510WBC+, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

TEST / PAIRING

SELECT

+Hr

SET

iOnce paired please close the

boiler control panel.

The LED will start flashing red.

TEST / PAIRING

+Hr

SELECT SET

RXWBC605 Installation

RXWBC605

Switch off the boiler at its main supply. Remove the outer casing and front fascia to

allow access to the main control panel.

Pull top tab B upwards, then outwards to

remove blanking plate or existing control.

Replace the front fascia and boiler’s

outer casing.

First plug in the connector block C

ensuring correct orientation. Remember

to ensure the block is fully connected.

Remove cover panel A upwards to remove.

Now locate the boiler control’s four hooks

then press in and down. Replace Cover

panel A.

The user can also move the switch to the OFF

position; when in this mode, the boiler will not

receive a signal from the RF thermostat.

The user can also move the switch to the

MANUAL ON position; when in this mode, the

boiler will be always turned on and the LED

indicator will also be lit constantly.

A – LED This LED will be on when the thermostat is

demanding heat.

B – Mode Switch:

MANUAL ON / AUTO / OFF

C – SYNC Button - This is used only for pairing the RF

communications.

Now move the switch back to .AUTO

To ensure the boiler control is connected properly, please now move the switch to

MANUAL ON . The boiler should now Fire and the LED on the your boiler

control should illuminate.

RXWBC605 Switch Position

RXWBC605 User Controls

When the switch on the Boiler Module is in

the AUTO position, the boiler control will

automatically receive the RF signal from the

thermostat and control the module output so

that it switches the boiler accordingly.

Before switching the boiler on at its mains supply, ensure the module switch is in the

OFF .position Ø

SYNC Button

Ensure the switch on the RF

integral boiler module is in the

AUTO position.

Gently press and hold the SYNC

button with a blunt object. After 3

seconds the Boiler Control LED will

flash once every second to indicate it

is ready to pair and ready to receive

a signal from the thermostat.

A B C

Quick Guide

Always isolate the AC Mains supply before installing or working on any components

that require 230 VAC 50Hz supply.

RT510WBC+ (Thermostat) Button Functions

Introduction

The RT510WBC+ thermostat will switch your heating system on or o, as needed, in accordance

with the time and temperature set by you. It can be used with the RXWBC605 integral plug-

in RF boiler control. The RF boiler control is a direct replacement for the basic time clock or

blanking plate usually supplied with the boiler. Installing the RF boiler control takes minutes.

Once installed, you will benefit from all the control features of the RT510WBC+ thermostat.

868.0-868.6MHz; <13dBm

Safety Information

Use in accordance with the regulations. Indoor use only. Keep your device completely dry. Disconnect

your device before cleaning it with a dry cloth. This accessory must be tted by a competent person, and

installation must comply with the guidance, standards and regulations applicable to the city, country or

state where the product is installed. Failure to comply with the relevant standards could lead to prosecution.

Product Compliance

This product complies with the essential requirements and other relevant provisions of the following EU Directives: EMC

2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of Conformity is

available on www.saluslegal.com

+Hr

SELECT

SET

Key Function

1. Press once to activate Frost Mode

2. Press for 3 seconds in order to activate Holiday Mode

Press once to activate/deactivate Boost function

Press once to enter/exit Permanent Override function

Increase button

Decrease button

Select the clock or programme settings

Press to conrm your settings

1. Press once to enter/exit in Test Mode

2. Press for 3 seconds to enter/exit Pairing Mode

Press the buttons for 3 seconds to enter Installer Mode

Press the buttons for 3 seconds to enter Clock Settings

Box content

Quick Guide 2 x AA Alkaline

Batteries 2 x Fixing Screws

RT510WBC+ Desk Stand

RT510WBC+ (Thermostat) Dip Switch Settings

Boiler may re up on pre-heat mode on rst turn on. If it does, it is advisable to

temporarily turn o your pre-heat until installtion is complete.

TEST / PAIRING

SELECT

+Hr

SET

TEST / PAIRING

SELECT

+Hr

3 Sec

TEST / PAIRING

+Hr

SELECT

Test the Pairing Process

Pairing Process

Once the LED stops flashing, press the

TEST / PAIRING button for 3 sec.

Begin the pairing process

End the pairing process

During test pairing, boiler control should ash conrming pair. If not, please follow

Pairing Process.

When enter test pairing

mode, after a 10 minute

countdown the thermostat

will time out.

SALUS Controls is a member of the Computime Group.

Maintaining a policy of continuous product development SALUS Controls plc reserve the right to

change speciﬁcation, design and materials of products listed in this brochure without prior notice.

Issue Date: February 2018

V016

For PDF Installation guide please go to www.salus-manuals.com

TEST / PAIRING

SELECT

+Hr

3 Sec

SALUS Controls plc

SALUS House

Dodworth Business Park South,

Whinby Road, Dodworth,

Barnsley S75 3SP, UK.

T: +44 (0) 1226 323961

E: sales@salus-tech.com

E: techsupport@salus-tech.com

www.salus-tech.com

PLUS

Internal Temperature

Load Compensation

The DIP Switches can be found on the rear of your thermostat. For all plug-in

boiler receiver applications ensure SW1 is set to RAD.

1 2

NA SPAN

RAD ITLC

Control feature ITLC SPAN

Operation ITLC Internal Temperature

Load Compensation for

improved eciency.

When Span is selected

on DIP switch № 2, the

DIP switch № 1 is not

functional.

+Hr

SELECT SET

Setpoint (desired) temperature

TEST / PAIR ING

Setting Time and Date

Programming

Press SET to return to the Main Screen.

+Hr

+Hr +Hr

+Hr

SELECT

SELECT SELECT

SELECT

SET

SET SET

SET

+Hr

SELECT SET

You can create personalized programmes for your controller. You have the option to choose

between a 5-2 days programme or a daily one by using the parameter d04 from Installer mode.

Press UP or DOWN to select Weekday/Weekend/

Day and press SELECT.

Press SET to change your programmes.

+Hr

SELECT SET

Press UP or DOWN to set the minutes and

press SELECT to conrm your option.

Press UP or DOWN to set the temperature and

press SELECT to conrm your option.

Follow the same procedure for the next

set of time.

Review the Setpoint (desired) temperature

Press UP or DOWN to review the setpoint

temperature.

Press UP or DOWN to set the temperature.

Actual room temperature

Boost function

Frost protection

Frost Mode ON.

+Hr

SELECT SET

Press OVERRIDE in order to activate the

mode. Press UP or DOWN to set the temperature.

+Hr

SELECT SET

Press SET to conrm the changes.

Press +Hr to activate the

Boost function.

Press the FROST button once to activate the

function.

The Override sign will appear on the Main

screen.

Press +Hr to set boost hours and then press

UP or DOWN to set the boost temperature

for your boost period.

+Hr

SELECT SET

Frost Mode OFF.

+Hr

SELECT SET

Holiday Mode

Press the HOLIDAY button for 3 sec. Press the UP or DOWN button to set the

Holiday period.

+Hr

SELECT SET

+Hr

SELECT SET

Press the HOLIDAY button for 3 sec to exit

Holiday Mode.

Reset function RT510TX+

Remove the batteries without pressing any button. Wait 2 minutes and insert the batteries

again. Your device will be restarted.

+Hr

SELECT SET

+Hr

SELECT SET

+Hr

SELECT SET

+Hr

SELECT SET

+Hr

SELECT ET

SELECT SET

+Hr

SELECT SET

Press UP or DOWN to set the hour and press

SELECT to conrm your option.

+Hr

SELECT SET

+Hr

SELECT SET

+Hr

SELECT SET

+Hr

SELECT SET

Permanent Override

5-2 Days Programme 24h Programme

Weekdays

6 sets of time/channel

Weekends

6 sets of time/channel

Total: 12 settings/week

24h

6 sets of time/channel

Total: 42 settings/week

TEST / PAIR ING TEST / PAIR ING

TEST / PAIR ING

TEST / PAIR ING TEST / PAIR ING

TEST / PAIR ING

TEST / PAIR ING TEST / PAIR ING

TEST / PAIR ING

TEST / PAIR ING TEST / PAIR ING

Continue with the same steps for setting

the Day.

Press the FROST button once to deactivate

the function.

Temporary Override

1 2

+Hr

SELECT SET

Press SET to conrm the changes.

+Hr

SELECT SET

TEST / PAIR ING TEST / PAIR ING

3sec

Press the buttons together for 3 sec.

Press UP or DOWN to select the hour format

and then press SELECT to conrm your

option.

Press UP or DOWN to select the hour

and then press SELECT to conrm your

option.

Press UP or DOWN to select the minutes

and then press SELECT to conrm your

option.

+Hr

SELECT SET

+Hr

SELECT SET

3 Sec3 Sec

+Hr

SELECT SET

+Hr

SELECT SET

TEST / PAIR ING

After you have done all the changes, please press SET to conrm all your choices

and to return to the Main Screen.

The Frost protection temperature can be reviewed by pressing the UP button

once, but can only be changed in Installer Mode.

iYou can also exit Holiday Mode by setting the days to zero.

When you want to change the batteries your device will use the internal

memory to backup your settings. You have 30 seconds to change the

batteries before losing your settings.

dxx Function Parameter Default value

d01 Temperature display increments 0.1°C or 0.5°C 0.5°C

d02 Temperature oset +/- 3.0°C 0.0°C

d03 Frost Protection setpoint temperature 5.0°C - 17.0°C 5.0°C

d04 Programmer selection 5/2 or 24 hr (7d) 52d

Installer Mode

Press the three buttons together

simultaneously for 3 seconds.

+Hr

SELECT SET TEST / PAIR ING

+Hr

SELECT SET

3 Sec

NOTE:

If you do not notice the “low battery” symbol displayed on the screen in time, it will shut

down. In this case, after removing the old batteries, it is necessary to wait 5 minutes before

inserting the new batteries. Otherwise, it is possible that a condenser will remain partially

discharged and it can prevent the thermostat from restarting.

Produkt Specifikationer

Mærke:	Salus
Kategori:	Termostat
Model:	RT510WBC+

Har du brug for hjælp?

Hvis du har brug for hjælp til Salus RT510WBC+ stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Salus Manualer

Salus SQ605RF Manual

30 Juli 2025

Salus 091PRO Manual

29 Juli 2025

Salus RT310SPE Manual

24 Juli 2025

Salus RT20 Manual

23 Juli 2025

Salus EL600F Manual

23 Juli 2025

Salus VS35B Manual

23 Juli 2025

Salus 091PRORF Manual

23 Juli 2025

Salus HTRP24 Manual

23 Juli 2025

Salus CB500X Manual

23 Juli 2025

Salus CB500 Manual

23 Juli 2025

Termostat Manualer

Nyeste Termostat Manualer

Honeywell RTH9580WF1005 Manual

14 August 2025

Honeywell YCT30A1003 Manual

14 August 2025

Honeywell RTHL3550D1006 Manual

14 August 2025

Honeywell YCT87K1003 Manual

14 August 2025

Honeywell CT30A1005 Manual

14 August 2025

Honeywell RTH6450D Manual

14 August 2025

Honeywell CT62B1015/U Manual

14 August 2025

Renkforce MH-810HN Manual

14 August 2025

Honeywell RTH2310B1002/A Manual

13 August 2025

Honeywell CT53K1006/E Manual

13 August 2025