Seco-Larm E-942FC-1K3SQ Manual

Seco-Larm Ikke kategoriseret E-942FC-1K3SQ

Læs gratis den danske manual til Seco-Larm E-942FC-1K3SQ (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 88 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 44.5 anmeldelser. Har du et spørgsmål om Seco-Larm E-942FC-1K3SQ, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Magnetic Gate Lock Bracket Installation Manual
SECO-LARM U.S.A., Inc.
Installation Manual
E-942FC-1K3SQ
E-942FC-600SQ
Electromagnetic Lock with
Weldable Brackets for Gates
NOTICE: The information and specifications printed in this manual are current at the time of publication. However,
the SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the
right to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole
or in part, without the written permission of SECO-LARM.
REGULAR MAINTENANCE
• Clean the contact surfaces of the electromagnet or armature plate with a soft cloth and non-abrasive, non-corrosive cleaner.
• Apply a light coat of a silicon lubricant to both contact surfaces and wipe away the excess to prevent rust.
• Check that the armature plate is securely attached to the bracket, yet can pivot slightly around the armature screw.
• Check that the electromagnet is securely attached to the bracket.
TROUBLESHOOTING
Possible cause:
No power
Poor contact between
electromagnet and
armature plate
Incorrect voltage setting
A secondary diode was
installed across the
electromagnet
Solutions:
• Check to make sure the wires are secure
• Check that the power supply is
connected and operating
• Make sure the unit is wired correctly
• Make sure the electromagnet and
armature plate are properly aligned
• Make sure the contact surfaces of the
electromagnet and armature plate are
clean and free from rust
• Check the power leads with a meter, and
make sure the correct voltage is present
• The electromagnet is fitted with a metal
oxide varistor to prevent interference, so
do not install a secondary diode
Problem:
Gate does not lock
Gate locks, but can be
easily forced open
Delay in gate releasing
• For most types of outdoor sliding and swinging electric gates.
• Includes a magnetic lock with brackets for armature and magnet.
• Brackets can be welded or bolted directly to gate.
• Holding force: E-942FC-1K3SQ – 1,300 pounds (591kg).
E-942FC-600SQ – 600 pounds (272kg).
• Brackets are zinc-plated for corrosion resistance.
• Brackets have black finish to match most gates.
• Water- and vandal-resistant attractive stainless-steel finish.
• Maintenance-free, factory-sealed design.
• Fail-safe operation (unlocks door if power is removed).
• Mounted vertically.
• Four knockouts on the junction box.
• Adapter and mounting hardware included.
• Voltage
—
12VDC or 24VDC. Prewired for 12VDC operation.
• Current draw
—
500mA @ 12VDC (250mA @ 24VDC).
MOUNTING THE ELECTROMAGNETIC LOCK
A. Determine type of gate:
1. Single-swing gate — Gate swings on one end, and comes to rest on a fixed gate post when closed. In this
case, a
typical installation has the electromagnet fixed to the gate post, and the armature connected to the free end
of the gate.
2. Double-swing gate — Two gates swing in the same direction when activated. The electromagnet is fixed to
the free end of one gate, and the armature is fixed to the free end of the other.
3. Sliding gate — The gate slides instead of swings away from a fixed gate post. A typical installation has the
electromagnet fixed to the gate post, and armature connected to the free end of the gate.
B. Mount the electromagnet — In most cases, the position of the electromagnet will determine the location of the
armature plate. Make sure there is space to run the cable.
1. Tack weld bracket into place. (Tack weld only.)
2. Dismount the electromagnetic lock from the bracket. Warning: Failure to remove electromagnetic lock will
result in severe damage to lock. Weld 3 or 4 beads about 1” apart. Make sure not to weld the junction box.
(See diagram for “No Weld” areas.)
3. Remount the electromagnetic lock.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
Website: www.seco-larm.com
E-mail: sales
@
seco-larm.com
UL CERTIFICATION
Electromagnetic lock only (Model E-942FC-1300/E-942FC-600) conforms to UL/10B
“Fire Tests of Door Assemblies”
and UL/10C “Positive Pressure Fire Tests of Door Assemblies” for swinging door assemblies.
It is also classified in accordance with the Uniform Building Code standard 7-2.
E-942FC-1K3SQ Shown
LIFETIME LIMITED WARRANTY: This SECO-LARM product is warranted against defects in
material and workmanship while used in normal service for the lifetime of the product. SECO-LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. Under no
circumstances will SECO-LARM be responsible for any costs or charges for removal, installation, or reinstallation.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair,
or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to repair or replacement only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else. This lifetime limited warranty is for products sold and installed in
the United States and Canada. For all other countries the warranty is 1 (one) year.
ECOS
SECOSECO
SECO
-
--
-
L R
L RLAR
LAR
M
MM
M
Page 1
(Magnetic lock only)
Page 4
PITSW1
FILE: DT/DTP/MiE-942FC-xxxSb.pmd
ORDER PART# 764-024%_077

Produkt Specifikationer

Mærke: Seco-Larm
Kategori: Ikke kategoriseret
Model: E-942FC-1K3SQ

Har du brug for hjælp?

Hvis du har brug for hjælp til Seco-Larm E-942FC-1K3SQ stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Seco-Larm Manualer

Seco-Larm

Seco-Larm SD-6276-SSVQ Manual

29 August 2024
Seco-Larm

Seco-Larm E-942FC-1K3SQ Manual

29 August 2024
Seco-Larm

Seco-Larm SD-6276-SS1Q Manual

29 August 2024
Seco-Larm

Seco-Larm E-936-S45RRGQ Manual

29 August 2024
Seco-Larm

Seco-Larm SD-969-S18Q Manual

29 August 2024
Seco-Larm

Seco-Larm E-941SA-600PQ Manual

29 August 2024
Seco-Larm

Seco-Larm SA-025Q Manual

29 August 2024
Seco-Larm

Seco-Larm SS-075CQ Manual

29 August 2024
Seco-Larm

Seco-Larm SD-6176-SS1Q Manual

29 August 2024
Seco-Larm

Seco-Larm SM-226LQ Manual

29 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kenu

Kenu Airframe Wireless AFW-KK-NA Manual

4 November 2025
Beverage-Air

Beverage-Air Horizon HF1HC-1HS Manual

4 November 2025
EKO

EKO K400FDGC Manual

4 November 2025
Intermatic

Intermatic OP5GY24 Manual

4 November 2025
Abus

Abus Secoris BUBE60020 Manual

4 November 2025
Hillvert

Hillvert HT-TEMPLE-1 Manual

4 November 2025
Yamazen

Yamazen KABF-120H Manual

4 November 2025
RADEMACHER

RADEMACHER RolloTron Standard 1300 Manual

4 November 2025
ANCEL

ANCEL MT700 Manual

4 November 2025
Schneider

Schneider Homeline HOM250PSPD Manual

4 November 2025