Star Micronics mC-Print3 Manual

Star Micronics Printer mC-Print3

Læs gratis den danske manual til Star Micronics mC-Print3 (2 sider) i kategorien Printer. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Star Micronics mC-Print3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Easy

Setup Guide

Safety

Instructions

This Manual

Power Cable*AC Adapter

MCP31CI

Easy Setup Guide

Installing the paper roll

Take the slack of the paper roll before paper

setting, install the paper roll as shown in the

illustration.

Pull the end of the paper roll out straight



, and use both hands to close the printer

cover



Pull the open lever



and open the printer

cover



ⓘ

When using a 58mm roll, install the

paper roll guide sold separately.

With the notch part A (triangle mark) of the

paper roll guide facing down, angle the

guide to the right and insert it



Position so that the notch part A is aligned

with the main unit rib B, then slide the

guide from the right



When the slid paper roll guide stops, stand

it up vertical



, and press until it clicks

into place



To change the paper width, it is necessary

to change the memory switch setting.

For details, refer to the Online Manual.

Turning ON the Main Unit Power

Press the power button



and confirm

that the LED (blue) illuminates



Connect the power cable to the AC adapter



, and connect the cable connector to the

printer as shown in the illustration



Insert the plug into the outlet



Place your nails into the gaps in the right

and left sides of the rear cover on the back

of the printer, and then remove the cover.

RE ET

RESET

80879110

Introduction

If contents are missing or damaged, please contact the reseller that sold you the printer.

*accessories vary depending on the region where the printer was purchased.

What's Included

This document explains the setup procedure for the mC-Print3.

For further instructions, please refer to the mC-Print3 (2nd Generation) online manual.

Please read the instructions before using the printer.

You can also see FAQ from the QR code on the inside of the printer.

FAQ

mC-Print3 online manual

For the owners of other companies’ trademarks mentioned in this document,see Trademarks in our website (https://www.star-m.jp/eng/trademarks.html).

Star Windows Software

When using Windows

Star Quick Setup Utility

When using Android iOS/





Once a static IP address is assigned, IP address changes through the DHCP server will not occur, so the specied connection destination

device can be used continuously once set.

Preparing/setting up the conguration app

Use the conguration app to set up the printer from a tablet or PC.

Scan the QR code on the right side or search the app to access the

download site.

Conguration app

download site



Install [ Star Quick Setup Utility ].



Open the conguration utility, and select [ Start Guide (Initial

Settings)] - [ Search Printer].



Follow the instructions of the utility to connect and set up a tablet.

ⓘ

For a wired LAN connection, use the tablet that is connected to

the same network as the MCP31CI.

ⓘ

The Windows driver is included in the Star Windows Software.

The Star Windows Software can be used to configure the

printer settings and perform an operation test.



Download [ Star Windows Software ].



Extract the downloaded software and execute “Setup.exe”.



Follow the wizard instructions and complete software installation.

ⓘ

Driver download site for Mac / Linux environment. (https://www.star-m.jp/supportsite-wsw.html)

Connecting a Tablet or PC

Prepare and connect an appropriate cable to the connector on the printer

according to your device/PC.

When using a commercially available cable, be sure to perform full operation checks

before use.

RESET

LAN

iPad

Android

Windows

USB-C

20W(USB PD)

Wired LAN

LAN cable

Plug for the printer:

ⓘ



DHCP is enabled by default for the wired LAN settings. To continually

use the same IP address, set a static IP address before use. For the static

IP address setting procedure, refer to the Online Manual.

ⓘ



If your PC cannot communicate with the printer using C to C cable, refer

to "Switching the USB-C function manually" on the back page of this

manual, and then switch the function to "Data only".

Communication and Recharge

USB-C

USB cable

(Make sure that the connector type is appropriate for your device/PC)

iOS … C to C

C to Lightning

Android … C to C

PC … C to A

(Communication only

)

C to C

Plug for the printer:

Cable that conforms to USB2.0 standards, supports current of 3.0A or

higher, and has a maximum length of 2 m.

Apple genuine cable or MFi certified cable with a maximum length of 2 m.

Cable that conforms to USB2.0 standards, has a maximum length of 2 m.

Cable that is compatible with category 5 or higher.

Produkt Specifikationer

Mærke:	Star Micronics
Kategori:	Printer
Model:	mC-Print3
Type:	POS printer
Bredde:	132 mm
Dybde:	140 mm
Højde:	125 mm
Produktfarve:	Sort
Wi-Fi:	Ingen
USB-port:	Ja
Opbevaringstemperatur (T-T):	-20 - 60 °C
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	10 - 90 %
Antal USB 2.0-porte:	4
Ethernet LAN:	Ja
Driftstemperatur (T-T):	5 - 45 °C
Udskrivningsteknologi:	Termisk
Maksimal opløsning:	203 x 203 dpi
USB-stik:	USB Type-A / USB Type-B
Intern hukommelse:	- MB
Forbindelsesteknologi:	Ledningsført
Certificering:	UL, C-UL, TuV, FCC, VCCI, EN55022, CE
Strømkilde type:	DC
Mac kompabilitet:	Ja
Understøttede mobile operativsystemer:	Android, iOS
Understøttede Windows-operativsystemer:	Windows 10, Windows 7, Windows 8.1, Windows Vista, Windows XP
Understøttede Mac-operativsystemer:	MacOS
Understøttet papirbredde:	80 mm
Udskrivningshastighed:	250 mm/sek.
Maksimal rullediameter:	83 mm
Indbyggede stregkoder:	MaxiCode, PDF417
Tykkelse af printmedier:	0.075 µm
Skæremaskine:	Ja