Statron 2223.2 Manual

Statron Ikke kategoriseret 2223.2

Læs gratis den danske manual til Statron 2223.2 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Statron 2223.2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Operating instruction lab

power supply unit

0 ... 32 V / 0 ... 3,0 A

type 2223.2

The intended application of the power supply unit covers:

- link and operation of low-voltage consumers with an operating voltage between 0 and 32 VDC. The power

input of the consumer may not exceed 3,0 A.

Note! Absolutely read!

- Read this guidance exactly. With damage, which is caused by neglect of the guidance, the warranty claim

goes out. For damages we do not take over adhesion.

Table of contents

1 introduction of

2 safety notes (mains connection and protection change) of

3 controls

4 line-up

5 technical data

1. introduction

this power supply unit is universally applicable with its infinitely variable adjustment possibilities of voltage and

current for school, occupation, hobby etc.. An electronic current limiting protects the power supply unit against

overloading. Output voltage and - current are electronically stabilized and infinitely variable adjustable. Thus the

electronic restraint current can as adjustable Current limiting to be used, in order to protect consumers against a

too high power input. In the case of an overloading the output voltage is then lowered accordingly (in the case of

short-circuit on close 0V). With removal of the overload the output voltage adjusted before resets itself

automatically. The respective operating point - voltage - (u) - or restraint current (i) - is displayed by one red

LED each. The adjusted values are readable over 2 LCD displays or analog displays each. The voltage or

current adjustment is made by one double button each (rough- fine). Additionally a change .

2. Safety notes

2,1 the power supply unit is in safety class system I as well as in accordance with VDE 0411 and VDE 0805

(EN60950) structured. The supply transformer is structured and with 3,75 kVeff is primary secondarily

checked according to DIN VDE 0551 as safety insulating transformer. It is radio-screened in accordance with

VDE 0875T11 curve B. Es is equipped with a VDE checked main with protective grounding and may

therefore only to 230-V-Wechselspannungsnetzen with protective grounding be operated or attached.

2,2 it is to be made certain that protective grounding (yellow/green) is interrupted neither in the main nor in the

device or in the network, since with interrupted protective grounding mortal danger exists. It is to be made

certain further that the isolation is damaged nor destroyed neither.

2,3 power supply units do not belong into child hands!

2,4 in commercial mechanisms is to be considered the rules for the prevention of accidents of the federation of

the commercial Professional association for electrical system and resources.

2,5 in schools, training facilities, hobby and self-help workshops. is by hand possible for

2,6 when opening covers or removing from sections, except if this, can live sections be opened. Also interface can

be live. Before an alignment, maintenance, a repair or an exchange of sections the device must be separate

from all voltage supplies, if opening of the device is necessary. If thereafter an alignment, maintenance or a

repair at the opened device under voltage are inevitable, may take place only by means of a specialist, who is

familiar with the associated dangers or the relevant regulations for it.

2,7 condensers in the device can be still loaded, even if the device were separated from all voltage supplies.

2,8 it is to be guaranteed that only protections of the indicated type and the indicated call stromstraerke are used

as back-up. The use of repaired protections or bridging the fuse holder is illegal. The device is overload-proof

and short-circuit-protected. When burning the input protection through a serious error is therefore present,

which must be eliminated by a specialist, before the new intact protection can be used by this specialist.

2,9 switching it your power supply unit never equivalent if it is brought by a cold into a warm space. The

condensation developing thereby can destroy your device under unfavorable circumstances. Let the device

unein switched to room temperature come. carrying of metallic or conductive decoration is forbidden to

2,10 with work with power supply units such as chains, bracelets, rings or the like.

2,11 power supply units are not certified for application at humans or animals.

2,12 during the series connection of the outputs one or several power supply units is produced lethal voltages (>35

VDC).

2,13 louvers of power supply units may not be taken off! The devices are on hard to place with difficulty

inflammable documents so that air can occur the devices unhindered. The cooling of the devices takes place

predominantly via convection.

2,14 power supply units and the attached consumers may not be operated unsupervised. Measures are to be

taken to the protection and the protection of the attached consumers in relation to effects of the power supply

units (e.g. overvoltages, failure of the power supply unit) and the effects and dangers outgoing from the

consumers themselves (e.g. illegally high power input). Note! Sensitive consumers must be protected

additionally by external measures against destruction!

2,15 in the event of an error can deliver power supply units voltages over 50 V DC voltage, from which dangers

proceed, also then if the indicated output voltages of the devices lower is situated.

2,16 with work under voltage for it expressly certified tools may be only used.

2,17 the outputs of the power supply units (exit hub/clamps) and to it attached lines must be protected against

direct contact. In addition the used lines must sufficient isolation or tension strain possess and the contact

points be contact-voltage-proof (safety sockets).

2,18 shifting metallically bright lines and contacts is to be avoided. All these places are by suitable to take and to

protect thus against direct contact with difficulty inflammable insulants or other measures off. Also the

electrically leading sections of the attached consumers are to be protected by appropriate measures against

direct contact.

2,19 if to assume it is that a safe operation is no longer possible, then is the device out of operation to set and

against unintentional operation protect. It is to be assumed that a safe operation is no longer possible, if - the

Produkt Specifikationer

Mærke:	Statron
Kategori:	Ikke kategoriseret
Model:	2223.2

Har du brug for hjælp?

Hvis du har brug for hjælp til Statron 2223.2 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Statron Manualer

Statron 3252.1 Manual

2 September 2024

Statron 3250.1 Manual

2 September 2024

Statron 2225.4 Manual

2 September 2024

Statron 2225.2 Manual

2 September 2024

Statron 5359.3 Manual

2 September 2024

Statron 3254.1 Manual

2 September 2024

Statron 3262.1 Manual

2 September 2024

Statron 2223.2 Manual

2 September 2024

Statron 2224.9 Manual

2 September 2024

Statron 3256.1 Manual

22 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

QSC RMXa Manual

13 September 2025

Tineco Floor One S2 Series Manual

13 September 2025

Tineco Floor One S3 Breeze Manual

13 September 2025

Tineco Floor One S5 Steam Manual

13 September 2025

Osram VX500-CB Manual

13 September 2025

Zelmer ZTS7990 Manual

13 September 2025

Osram VX250-SP Manual

13 September 2025

Vello CB-800 Manual

13 September 2025

Ibm System Storage ProtecTIER TS7620 Manual

13 September 2025

Ibm System Storage N6250 Manual

13 September 2025