Sunding SD-590C Manual

Sunding Ikke kategoriseret SD-590C

Læs gratis den danske manual til Sunding SD-590C (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Sunding SD-590C, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
-TRIP UP TRIP DISTANCE COUNT UP
-TRIP DN TRIP DISTANCE COUNT DOWN
-CAL CALORIE
-FAT FATBURN
-COMPARATOR
-Km/Mile SELECTION
-SLEEP MODE
- MAINTENANCE ALERT
- SETTING TYRE CIRCUMFERENCE
-SETTING LAST VALUE OF ODOMETER/ODO
-SETTING TTM
-COMPUTER LOW BATTERY INDICATOR
-SENSOR LOW BATTERY INDICATOR
- AUTO BACK LIGHT
-WIRELESS AUTO WAKE UP
- AUTO ON/OFF
SD 590C- V1 . 0
FUNCTIONS ILLUSTRATIONS
WHAT IS IN THE PACKAGE
COMPONENT ILLUSTRATIONS
-SPD CURRENT SPEED
-ODO ODOMETER
-DST TRIP DISTANCE
-MXS MAXIMUM SPEED
-AVS AVERAGE SPEED
-TTM TOTAL TRIP TIME
-TM TRIP TIME
-RAT RIDING ALL TIME (SINGLE TRIP TIME)
-CLK CLOCK 12H/24H
-SW STOPWATCH
-Th TEMPERATURE
-MAX Th MAXIMUM TEMPERATURE
-MIN Th MINIMUM TEMPERATURE
-TM UP TRIP TIME COUNT UP
-TM DN TRIP TIME COUNT DOWN
1
2
35
6
4
3mm
Computer unit and mount installation
Insert com puter unit
in to th e mount.
2 Mount the mount
shoe on to the
handlebar.
3
Close
Ope n
Coi n
To attach the speedometer sensor, use the ties to secure it to the front
fork. Make sure the computer and the sensor are on the same side of
the fork and no more than 60cm apart. The sensor should have an
arrow pointing at the magnet. Follow the figure to install the magnet on
a spoke. The gap between the sensor and the magnet should be 3 mm.
Notice
The magnet is designed for spokes
that are less than 2mm thick
Pass bicycle spokes through the
plastic hole on the bottom of the
magnet and tighten to secure
Computer
CR2032 Battery
Magnet
Mounting Shoe
Sensor
Ties
1
2
3
4
5
6
Please note that the slight noise when the computer unit shakes is the built-in ball switch, which is a
normal phenomenon caused by the wireless automatic wake-up function design.
Tighten nut to
scure the unIt.
Installation diagram of
magnet and Sensor
INSTRUCTION
Avoid exposing the device to direct sunlight or high temperature for too
long. Let it cool down in the shade for a while.
3.Black display
4.Display shows incomplete figures.
5.Display readout fades out
1.The speedometer shows 0 km/h while riding.
Improper magnet/sensor alignment, or the distance between
the computer and the sensor is more than 80cm.
2.The speedometer shows wrong values.
Take out the battery and reset it after 10 seconds.
Poor battery contact or dead battery .Check the installation of the battery or change a new battery.
The battery voltage is low, change a new battery.
MALFUNCTIONS AND REASONS
MODE INSTRUCTION
After inserting the battery, the screen enters the total distance/time mode. Press the MODE button to cycle through single
distance/time mode, count up/down mode and fat/calorie mode in turn. In the total distance/time mode, count up/down
mode and fat/calorie mode, it will automatically return to the single distance/time modeafter 8 seconds of no operation.
ODO / TTM MODE DST / TM MODE CAL / FAT MODECOUNTUP / DOWN MODE
1
FRON T BACK
COMPUTER &
MOUNTING
SHOE TRIGGER
BATTERY
COVER
MAINTENANCE ALERT
COMPARATOR
LOW BATTERY INDICATOR
Computer unit interface
MODESET
SPEED
TIME
Computer Unit SettIng
DST
SPD
The screen always shows the speed, which can go up to
99.9 km/h (m/h) with an accuracy of +/- 0.1 km/h (m/h).
SPD COMPARATOR
ODO
The screen shows the total distance in ODO mode, which
can be 0 to 99999 km (mile). The value resets to 0 after
reaching the maximum limit.
MAX SPD
AVS SPD
SPEED UNIT SETTING (KM/H)/(MILE/H)
To choose between kilometers per hour (km/h) or miles per hour (m/h) for the
speed unit, press the MODE button in the speed unit setting mode. Then press
the SET button to go to the odometer setting mode.
During riding,“ ” and “ ”on screen indicates the current
speedis higher or lower than average speed(AVS)
ODOMETER SETTING
The bottom line shows the single trip distance in DST
mode, which can be 0 to 9999 km (m). The value resets to
0 after reaching the maximum limit.
To set the odometer, press the MODE button to cycle through the flashing digits
and press the SET button to move to the next digit. The default value is 0000
and it can range from 0 to 99999 km or miles. After setting the odometer, press
the SET button to go to the total riding time setting mode.
To set the total riding time, press the MODE button to cycle through the flashing
digits and press the SET button to move to the next digit. The default value is
00:00:00 and it can range from 0 to 9999 hours. After setting the total riding
time, press the SET button to go to the maintenance alert setting mode.
In ODO or TTM mode, press SET to start stopwatch,
pressSET again to stop stopwatch. Long press SET for 3
seconds to clear the stopwatch data.
CLEAR ALL DATA
In DISPLAY mode press the SET button for 3 seconds to clear all the data ,
includingthat for DST MAX/ AVS TM RAT / / / / MAX TH/ MIN TH.
( \ \ except that for CLK ODO RAT TRIP UP TRIP DN TM UP TRIP DN\ \ \ \ )
TTM (SINGLE TRIP TIME) SETTING
TM UP AND TRIP UP RESET
In the distance/time countdown (TM/TRIP DN) mode, press SET button to
enter the distance/time count up (TM/TRIP UP) mode. In the distance/time
count up mode, press and hold MODE button for 3 seconds to clear the
distance/time count up data.
TM DN AND TRIP DN SETTING
To set the trip time/trip distance count down, press the SET button for 3 seconds in
the trip time/trip distance count down mode to enter setting mode, then press the
MODE button to change the flashing digits and press the SET button to move to
the next digit. The default values are 000.0 for trip distance count down (0 to 999.9
km or mile) and 00:00:00 for trip time count down (0 to 99:59:59 hours). Press the
SET button to go back to the trip time down and trip distance down mode once
finish setting.
The screen turns off after 300 seconds of no movement, but
the clock remains on display. You can turn on the screen by
shaking the bike or pressing any key, the computer unit will
return to the last used mode and preseve all the data
collected.
SLEEP MODE
TEMPERATURE
CARE REMINDER
Shows the ambient temperature in Celsius or Fahrenheit.
TheCelsius range is -20 to 70 degrees. The Fahrenheit
range is -4 to 158 degrees.
MAXIMUM TEMPERATURE
MINIMUM TEMPERATURE
TRIP TIME DOWN / TRIP DISTANCE DOWN
TRIP TIME UP / TRIP DISTANCE UP
The distance counts up from zero when riding, and the
maximum value is 9999.9. After that, it resets to zero and
counts again. The time counts up from zero when riding,
and the maximum value is 99:59:59. After that, it resets to
zero and countsagain
STOPWATCH
RAT
Travel time .RAT ranges 0~9999hours.
TM
TTM
After resetting the data, the trip time starts from zero and
counts up to 999 hours. After that, it resets to zero and
counts again.
Total riding time for one trip .TTM ranges 0~9999hr.
TEMPERATURE UNIT (C/F°) SETTING
Time Format (12H/24H) SETTING
After enters setting mode, press the MODE button to select between
Celsius or Fahrenheit . Then press the SET button to go to the clock
setting mode.
In Clock setting, press the MODE button to choose between 12H or 24H format,
then press the SET button to go to the hour setting mode and change the hour
value with the MODE button. Repeat the same steps for the minute setting, then
press the SET button to go to the tire circumference setting mode.
To set the tire circumference, use the chart to the right to find
the data for your tire size. The default value is 2080 mm. Press
MODE button to cycle through the flashing digit and Press SET
button to confirm and move to next digit. The value can range
from 0 to 9999 mm. After finishing circurence setting, press
SET button to go to the speed unit setting.
TIRE CIRCUMRENCE SETTING
FUNCTIONS
When the riding distance is greater, than the set
maintenance distance. the icon will appear, press both
the SET and MODE button at the same time to clear it.
12x1.95 940
14x1.75 1055
16x1.50 1185
16x2.00 1245
17x1-1/4 1340
18x1.50 1340
18x1.75 1350
20x1.25 1450
20x1.35 1460
20x1.50 1490
20x1.75 1515
20x1.95 1565
22x1-3/8 1770
22x1-1/2 1785
24x1.75 1890
24x2.00 1925
24x2.125 1965
24x1-1/8 1795
24x1-1/4 1905
26x1.25 1950
26x1.40 2005
26x1.50 2010
26x1.75 2023
26x1.95 2050
26x2.10 2068
26x2.25 2070
26x2.35 2083
26x3.00 2170
26x1-1/8 1970
26x1-3/8 2068
26x1-1/2 2100
650x20C 1938
650x23C 1944
650x25C 1952
650x38A 2125
650x38B 2105
27x1-1/8 2155
27x1-1/4 2161
27x1-3/8 2169
27.5x1.50 2079
27.5×1.95 2090
27.5x2.1 2148
27.5x2.25 2182
700x18C 2070
700x19C 2080
700x20C 2086
700x23C 2096
700x25C 2105
700x28C 2136
700x30C 2146
700x32C 2155
700x35C 2168
700x38C 2180
700x40C 2200
700x42C 2224
700x44C 2235
700x45C 2242
700x47C 2268
29x2.1 2288
29x2.2 2298
29x2.3 2326
TIRE S IZ E
CIRC
FATBURN FAT
CALORIE CAL
SENSOR LOW BATTERY INDICATOR
COMPUTER LOW BATTERY INDICATOR
AUTO WAKE UP
MAINTENANCE ALERT SETTING
KM
Enter Setting Mode
In any mode Long press SET+MODE button for 3 seconds to enter setting mode，.
To set maintenance alert, press the MODE button to adjust the flashing
value. The adjustment values are: 200, 400, 600, 800. After setting the
alert, press the SET button to enter the display mode.
CALORIE / FAT RESET
In the fat/calorie mode, press and hold the SET button for 3
seconds: fat and calorie data are cleared, other data are retained.
After resetting the data, the highest speed during the trip
is shown. Press SET in the DST/TM mode to see the
highest speed on the first line. Goes back to current speed
after 8 seconds.
After resetting the data, the average speed during the trip
is shown. Press SET in the DST/TM mode to see the
average speed on the first line. Goes back to current
speed after 8 seconds.
The distance counts down from the set value, and it
becomes negative when it reaches zero. It stops counting
when it gets to -999.9.
Maximum ambient temperature in a single trip.
Minimum ambient temperature in a single trip.
Shows fat burned after last data reset.
Shows calories burned after last data reset.
AUTO BACKLIGHT
The device automatically senses the brightness of the
environment. When ambient light is insufficient, you can press
any key to light up the screen for 5 seconds. When there is
enough ambient light, the screen will not light up when you
press any key. You can press and hold MODE key for 3
seconds to keep the screen on or off.
When the Sensor battery voltage is low, sensor low
voltage symbol appears on the screen. The symbol
disappears when you change the battery.
When the device is in sleep mode, it will enter working mode
when viberation being detected.
When the computer battery voltage is low, computer low
voltage symbol appears on the screen. The symbol
disappears when you change the battery.

Produkt Specifikationer

Mærke: Sunding
Kategori: Ikke kategoriseret
Model: SD-590C

Har du brug for hjælp?

Hvis du har brug for hjælp til Sunding SD-590C stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Sunding Manualer

Sunding

Sunding SD-536B Manual

31 Januar 2025
Sunding

Sunding SD-589 Manual

31 Januar 2025
Sunding

Sunding JOY-651 Manual

31 Januar 2025
Sunding

Sunding SD-581C Manual

31 Januar 2025
Sunding

Sunding SD-590A Manual

29 Januar 2025
Sunding

Sunding SD-579 Manual

29 Januar 2025
Sunding

Sunding SD-590C Manual

29 Januar 2025
Sunding

Sunding SD-581G Manual

29 Januar 2025
Sunding

Sunding JOY-583C Manual

28 December 2024
Sunding

Sunding SD-521 Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

T'nB

T'nB MHMECA Manual

18 September 2025
Marmitek

Marmitek BoomBoom 55 HD Manual

18 September 2025
CTA Digital

CTA Digital PAD-HFS Manual

18 September 2025
Vestil

Vestil ATP-C-2436 Manual

18 September 2025
Active Intent Play

Active Intent Play GSBV16T Manual

18 September 2025
Vestil

Vestil D-33-MD Manual

18 September 2025
Vestil

Vestil LAD-13-14-P Manual

18 September 2025
Cambro

Cambro VBRTHD6110 Manual

18 September 2025
Vicoustic

Vicoustic VicFix Base Manual

18 September 2025
Vestil

Vestil LAD-10-14-P Manual

18 September 2025