TCW Technologies IFC-10 Manual


Læs gratis den danske manual til TCW Technologies IFC-10 (11 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om TCW Technologies IFC-10, eller vil du spørge andre brugere om produktet?

Side 1/11
1 Rev 1.1 © 2015 TCW Technologies, LLC
Intelligent Flap Controller
with positioning set-points
Model: IFC-10
Flap positioning and control system
for DC motor actuators up to 10 amps
Pilot and Co-pilot control
Vfe protection
Programmable positions and manual mode
2 Rev 1.1 © 2015 TCW Technologies, LLC
Intelligent Flap Controller (IFC) is an electronic controller designed
specifically to operate DC motor actuators including the Van’s Aircraft series of
Flap Actuators used in RV type homebuilt aircraft. IFC connects to the standard
up-off-(down) switches commonly used to control flap operation and directly
drives a Van’s flap actuator. IFC allows for Pilot and Co-pilot flap switches and
resolves the possible conflicts if the switches are operated in opposite directions.
IFC requires NO flap position sensor and is fully compatible with Safety-Trim
servo controllers.
IFC provides flap positioning presets that are easily set without having to
adjust a position sensor. Additionally, IFC includes a manual mode of operation
to raise or lower the flaps in proportion to the time the flap switch is held closed.
IFC receives switch inputs from Pilot and Co-pilot flap switches such as
those found on the Infinity Stick Grips. These switches provide a momentary
closure for Flaps Down and a maintained closure for Flaps UP. The switch
closures are referenced to a common ground. Based on the switch inputs, IFC
directly drives the flap actuator. IFC resolves any conflicts between the Pilot and
Co-pilot switches as well as any switches left in the maintained UP position.
Flap positions such as 0,10,20,40 degrees are selected by simply
pressing the flaps down switch for a momentary action of less than 1 second. If
flap positions other than those preset in the controller are desired the switch may
be held for longer than 1 second, giving manual control of flap position. When
the switch is released the flaps stop at their current position.
Additionally, when used with an ASW-1 airspeed switch IFC provides Vfe
protection by preventing flap deployment above a preset air speed. However,
IFC will not limit the flaps from being retracted regardless of airspeed.
The ASW-1 airspeed switch may be shared with a servo controller Safety-Trim
for system integration.
The Van’s flap actuators have no internally electrical limit switches and will
run continuously if not controlled. IFC prevents the flap actuator from running
endlessly when a flap switch is left in the UP position. After a 15 second
timeout, the flap actuator is shut off. Simply move a flap switch to the off or
down position to reset the operation of the flap actuator.
IFC is to be used with DC Flap Actuator motors rated for operation at 12-
24 volts DC and up to 10 amps continuous, 15 amps peak. No other uses are
permitted. The Flap Actuator must be mechanically or electrically limited for
travel length as the IFC unit does not set the minimum and maximum travel
lengths for the flap actuator. The Van’s flap actuator satisfies this requirement.
IFC is not TSO’d and must only be used in aircraft certified in the
Experimental category.
Flap input switches for DOWN actuation must be of the momentary
closure type. Flap input switches for UP actuation may be either momentary or
maintained type.
Compatible wiring harness model number: IFC-10-Harn


Produkt Specifikationer

Mærke: TCW Technologies
Kategori: Ikke kategoriseret
Model: IFC-10

Har du brug for hjælp?

Hvis du har brug for hjælp til TCW Technologies IFC-10 stil et spørgsmål nedenfor, og andre brugere vil svare dig