Atdec TH-3070-UT Manual

Atdec Flad panel støtte TH-3070-UT

Læs gratis den danske manual til Atdec TH-3070-UT (2 sider) i kategorien Flad panel støtte. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Atdec TH-3070-UT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Bits Bag

Component Checklist

Display Bracket (left)

Display Bracket (right)

Installation Instructions

FLAT SCREEN WALL MOUNT | TILTTH-3070-UT

Wall Plate

Important Notes

TOOLS REQUIRED:



Power Drill



12mm (

”), 10mm (

”) or

7mm (

”) Drill Bit



Phillips Head Screw Driver



Spirit Level



17mm (

”) Socket Wrench

or Shifter

Supports a maximum load of 91kgs (200lbs).

Suits displays with mounting hole patterns from 180mm to 810mm wide (7”-31

”) by 125mm to 500mm

high (5”-19

”).

The manufacturer does not accept responsibility for incorrect installation.

Security Bracket

Mounting Screws

M8x15mm / M8x35mm / M8x45mm (x4 each)

M6x15mm / M6x35mm / M6x45mm (x4 each)

M5x15mm / M5x35mm / M5x45mm (x4 each)

M4x15mm / M4x35mm / M4x45mm (x4 each)

Cross Recessed Screws

Mounting the Wall Plate

Masonry Wall

Washer

Masonry

Wall Plug

Wall Plate

12mm (

”)

Hole

Coach Screw

Dry Wall Timber Stud Wall

TIP: Use a spirit level to

ensure the wall plate is

horizontal

TIP: Use a spirit level to

ensure the wall plate is

horizontal

TIP: Use a spirit level to

ensure the wall plate is

horizontal

Wall Plate

Coach Screw

Washer

Timber

Stud

10mm (

”)

Hole

Wall Plate

Dry Wall

Anchor

Dry Wall

Anchor Screw

Dry Wall

Anchor Washer

Use a stud finder to precisely

locate the timber stud and

ensure that the mounting holes

are located in the centre of

the stud.

It is recommended when

mounting directly into masonry

wall, that the mounting holes

are positioned as far apart as

possible.

7mm (

”)

Hole

Note: Ensure the Wall Plate

is mounted with the folded

tabs pointing upwards.

Note: Ensure the Wall Plate

is mounted with the folded

tabs pointing upwards.

Note: Ensure the Wall Plate

is mounted with the folded

tabs pointing upwards.

Coach

Screw (x4)

Masonry Wall

Plug (x4)

Washer (x4)

Multi

Washer (x4)

Dry Wall

Anchor (x6)

The dry wall anchors provided in

the bit bag have been tested for

this wall mount application and will

each hold in excess of 30kg per

anchor.

Before using the expanding

anchors, please ensure that you:

· Check the plaster board wall (dry

wall) is in good condition with no

cracks, peeling paper or signs of

water damage etc.

· Take care installing the anchors,

that they are not over tightened

or driven into the wall during

installation.

· Minimum thickness of drywall

should be no less than 12mm (

”)

· Recommend to use all 6 anchors

even with light monitor applications.

· Only use the anchors supplied

in the kit.

· Make sure the 10mm (

”) pre-

drilled hole is as recommended and

no smaller or larger.

· The anchors during expansion

should not interfere with studs or

noggins (cross strengtheners).

™

13mm Spacer

Bush (x4)

20mm Spacer

Bush (x4)

Produkt Specifikationer

Mærke:	Atdec
Kategori:	Flad panel støtte
Model:	TH-3070-UT
Bredde:	845 mm
Dybde:	72.5 mm
Højde:	535 mm
Produktfarve:	Sort
Monteringstype:	Væg
Hældningsvinkelområde:	-5 - 15 °
Skærmstørrelse kompatibilitet:	32 - 65 "
Vægt (efter britisk standard):	200 Pund
Monteringsgrænseflade:	VESA 100mm x 200mm / 200mm x 200mm, nonVESA 180mm x 800mm / 100mm x 500mm
Vægt (maks.):	91 kg