Atdec TH-CM-SH-2 Manual

Atdec Flad panel støtte TH-CM-SH-2

Læs gratis den danske manual til Atdec TH-CM-SH-2 (2 sider) i kategorien Flad panel støtte. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Atdec TH-CM-SH-2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Shelf (x2)
TM
Component Checklist
Installation Instructions
TELEHOOK
Cable Manager Shelf System
Bits Bag
A Installation Options
Screw (x8)
2mm Allen Key
Check you have received
all parts against the
Component Checklist
If you already have the
Telehook Cable Manager
installed.
Begin by removing the Front Fascia and
the End Caps as shown. Once
complete, continue to step B below.
Option 1
If you are installing both
the Telehook Cable Manager and Telehook Cable
Manager Shelf System at the same time.
Begin by mounting the Wall Plate as shown in step A on the
Telehook Cable Manager Installation Instructions. Once complete,
continue to step B below.
Option 2
If your display is already wall mounted, depending on its position, it may be best to remove the display,
as it may interfere with the installation of the Telehook Cable Manager and Cable Manager Shelf System.
B Installing Telehook Cable Manager Shelves
Push one edge of the
Front Fascia until it
pops open
B.1.
Slide the Cable Manager Shelf
onto the Cable Manager Wall
Mount
Adjust the Cable Manager
Shelf to the
desired height
B.2.
Secure in place using the M4 Grub Screws and
the 2mm Allen Key supplied
B.3.
Remove End
Caps
Note:
If the mounted height of the display is
less than the length of the Telehook
Cable Manager, you may need to reduce
the length by cutting it to size.
(Consult a professional at this stage)
TOP VIEW
The Telehook Cable Manager Shelf System MUST be used in
conjunction with the Telehook Cable Manager.
Each Telehook Cable Manager is limited to a maximum of 4 Shelves.
Each Shelf supports a maximum weight of 20kgs (44lbs).
If you wish to paint your Cable Manager Shelves, please consult your
paint specialist for advice.
IMPORTANT NOTES
OR
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 24.09.07©
C Install your Equipment
Install or reinstall your display
Place your Audio/Video equipment on the Telehook Cable Manager Shelves
Connect all required cables to Audio/Video equipment
D Installing Cables
Display on
wall mount
bracket
Wall Plate
Install the display’s cables into the left,
right and centre cable bays as shown
E Insert Cable Clips
Cable
Tab
F Attach End Caps
TOP VIEW
Attach an End Cap onto
both ends of the Wall
Plate and secure in place
using the M4 Grub
Screws as shown.
NOTE:
If possible, separate the display’s
power cable from the data cables
(i.e. hi-fi & speaker cables) by
installing them into separate cable
bays. This will reduce the chance of
electromagnetic interference. The
diagram to the right shows an
example installation setup.
Left cable bay
Centre cable bay
(best for display power cable)
Right cable bay
Data cables
(can also be installed
into the same bay)
TOP VIEW
Using two hands,
flex the End Cap
around the
display’s cables
and manoeuvre
them into their
corresponding End
Cap Cable Bay
End Cap Cable Bay
E.2.
Twist the Cable
Tabs into the small
slots in the Wall
Plate
Display Power
cable
2mm
Allen
Key
M4
Grub
Screw
WARNING: DO
NOT OVER TIGHTEN
G Insert Front Fascia
G.2.
Partially insert the front
fascia as shown above
TOP VIEW
G.3.
Push the edge of the
Front Fascia until it
snaps into place
G.4.
Repeat G.3.
down the
length of the
Front Fascia
until it is firmly
secured onto
the Wall Plate
A
B
Installation Complete
Shelf
G.1.
Slide the Front
Fascia through the
cut outs in the
Shelves
Insert the Cable Tabs into
the Wall Plate to Secure
Cables in place.
If required, cables can exit
from the side of the Cable
Manager. In this case, use
the left or right cable bays
only.
Cables exiting from the side
E.1.
Using your
thumb and
index finger,
flex the Cable
Tab into a
concave shape

Produkt Specifikationer

Mærke: Atdec
Kategori: Flad panel støtte
Model: TH-CM-SH-2

Har du brug for hjælp?

Hvis du har brug for hjælp til Atdec TH-CM-SH-2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Flad panel støtte Atdec Manualer

Atdec

Atdec AWMS-HXB-H Manual

30 Januar 2025
Atdec

Atdec AWM-W Manual

30 Januar 2025
Atdec

Atdec AWMS-DW Manual

30 Januar 2025
Atdec

Atdec AWMS-DW6-S Manual

7 December 2024
Atdec

Atdec AWM-W-S Manual

7 December 2024
Atdec

Atdec AWMS-46W35-S Manual

7 December 2024
Atdec

Atdec AWMS-HX40-H-B Manual

7 December 2024
Atdec

Atdec AD-WF-8060 Manual

7 December 2024
Atdec

Atdec AD-WT-8060 Manual

7 December 2024
Atdec

Atdec AD-WF-10090 Manual

7 December 2024

Flad panel støtte Manualer

Nyeste Flad panel støtte Manualer

Chief

Chief MWCU Manual

3 April 2025
Chief

Chief KITXWXSM1U Manual

3 April 2025
Chief

Chief RLXT3 Manual

3 April 2025
Anywhere Cart

Anywhere Cart AC-GO-16 Manual

2 April 2025
Proaim

Proaim P-DMC Manual

2 April 2025
Proaim

Proaim CT-VNGD-CS Manual

2 April 2025
Mount-It!

Mount-It! MI-7919 Manual

2 April 2025
Mount-It!

Mount-It! MI-384 Manual

2 April 2025
Proaim

Proaim CT-VNGD-UC5 Manual

2 April 2025
Premier Mounts

Premier Mounts 7170-0977 Manual

2 April 2025