Brawa 0635 BR 06 001 (HO) Manual

Brawa Modelbygning 0635 BR 06 001 (HO)

Læs nedenfor 📖 manual på dansk for Brawa 0635 BR 06 001 (HO) (20 sider) i kategorien Modelbygning. Denne guide var nyttig for 21 personer og blev bedømt med 4.5 stjerner i gennemsnit af 11 brugere

Side 1/20
Die Deutsche Reichsbahn Gesellschaft schrieb 1934 den Bau einer
vierfach gekuppelten Schnellzuglok aus. Den Auftrag für den Bau von
zunächst zwei Lokomotiven der Baureihe 06 erhielt die Firma Krupp
in Essen. Der Bau der Dampflok BR 06 001 dauerte von 1934 bis
1939. Diese lange Bauzeit lässt sich nur damit erklären, dass schon
bald nach der Auftragserteilung das Interesse der DR an dieser
„Riesenlokomotive“ schwand. Als die Dampflok 06 001 im März 1939
ausgeliefert wurde, war bereits die Realisierung der Baureihe 01.10
als neue Generation schwerer Schnellzugloks beschlossen worden.
Die Baureihe 06 hatte Treibräder von 2000 mm Durchmesser und je
ein vorderes und hinteres Drehgestell. Das Dreizylinder-Triebwerk
sollte Laufruhe bis zu einer Höchstgeschwindigkeit von 140 km/h
ermöglichen. Gekuppelt mit dem 5-achsigen Tender T38St hatte die
BR 06 eine LüP von 26520 mm und war so die größte deutsche
Schnellzuglok. Die Reibungslast betrug 80 t, die Dienstlast der Lok
141 t, das Gesamtgewicht von Lok und Tender 224 t. Sehr zufrieden
war man mit dem Fahrwerk der Baureihe 06, mehrere zeitgenössi-
sche Berichte heben ausdrücklich den ruhigen Lauf der Maschine
auch bei hohen Geschwindigkeiten hervor. Die hohe Zugkraft weckte
ebenfalls Begeisterung. Weniger zufriedenstellend war dagegen der
Betrieb mit dem Kessel, der mit 7,50 m Rohrlänge zum Problemkind
geworden war. Das von der Reichsbahn verfochtene Prinzip des Lang-
rohrkessels mit kleiner Feuerbüchsheizfläche war in eine Sackgasse
geraten. Bis 1952 standen die Loks in Frankfurt und Hanau, dann
wurden sie in Darmstadt und Braunschweig verschrottet.
Ausführung Gleichstrom 0636
Ausführung Wechselstrom 0637
Betriebsanleitung
Dampflokomotive mit
Schlepptender BR 06 001 – H0
1
Operating Instructions
Direct current model 0636
Alternating current model 0637
In 1934, the Deutsche Reichsbahn Gesellschaft gave out an invitation
to tender for the construction of an express train with four
couplings.The initial construction order was for two locomotives from
the 06 series and was awarded to Krupp in Essen. The construction
of the steam locomotive BR 06 001 took from 1934 to 1939. This
long construction time can only be explained by the fact that shortly
after the order was given, DR’s interest in the “giant locomotive” faded.
When the locomotive was finally delivered in March 1939, the decision
to realise the 01.10 series, a new generation of heavy express train
locomotives, had been made. The 06 series had driving wheels with
a diameter of 2000 mm and both a front and rear bogie. The three-
cylinder valve gear and connecting rods was supposed to enable easy
running up to a top speed of 140 km/h. When coupled to the 5-axle
tender T38St, the BR 06 had an total length of 26 520 mm which
made it the largest German express train. The frictional load was 80t,
the locomotive’s service weight was 141t, the total weight of the
locomotive and tender was 224t. They were very pleased with the
chassis of the 06 series, several reports of the time expressly
complimented on the smooth running of the machine even at high
speed. The high level of pulling power was also cause for enthusiasm!
Less satisfactory however, was the tank which had become a problem
with its 7.5 m long pipe. The principle which the Reichsbahn favoured,
the long piped tank with small firebox heating surfaces, had come to
a dead end. Until 1952 the locomotives stood in Frankfurt and Hanau
and then they were scrapped in Darmstadt and Braunschweig.
Instructions de service
Modèle à courant continu 0636
Modèle à courant alternativ 0637
En 1934, la „Deutsche Reichsbahn“ (compagnie des chemins de fer
du Reich allemand) fit un appel d’offres pour la construction d’une
locomotive de train rapide à attelage quadruple. La société Krupp
d’Essen reçut, pour commencer, la commande de deux locomotives
de la série 06. La construction de la locomotive à vapeur BR 06 001
dura de 1934 à 1939. Cette longue durée de construction ne peut
sexpliquer que par le fait que pour la DR cette locomotive
gigantesqueperdit de son intérêt. Lorsqu’en mars 1939, la locomotive
à vapeur 06 001 fut livrée, la réalisation de la série 01.10 en tant que
nouvelle génération des locomotives lourdes des trains rapides, était
déjà décidée. La série 06 avait des roues motrices de 2000 mm de
diamètre et respectivement un bogie avant et arrière. Le mécanisme
moteur à trois cylindres devait permettre une marche silencieuse
jusqu’à une vitesse maximale de 140 km/h. Attelée au tender à 5
essieux T38St, avec une longueur hors tampons de 26 520 mm, la
BR 06 était la plus grande locomotive allemande. La charge de friction
était de 80 t, la charge de service de la locomotive de 141 t, le poids
total de la locomotive et du tender de 224 t. On était très satisfait du
canisme de roulement de la rie 06, plusieurs rapports de l’époque
soulignent expressément la marche silencieuse de la machine, même
à grandes vitesses. La grande capacité de traction était aussi source
d’enthousiasme. Mais par contre, le service de la chaudière était moins
2
Locomotive with trailing tender BR 06 001 – H0
Locomotive à vapeur à tender séparé BR 06 001 H0


Produkt Specifikationer

Mærke: Brawa
Kategori: Modelbygning
Model: 0635 BR 06 001 (HO)

Har du brug for hjælp?

Hvis du har brug for hjælp til Brawa 0635 BR 06 001 (HO) stil et spørgsmål nedenfor, og andre brugere vil svare dig