Code Corporation CodeXML M2 Manual

Code Corporation Netværkskort/adapter CodeXML M2

Læs gratis den danske manual til Code Corporation CodeXML M2 (2 sider) i kategorien Netværkskort/adapter. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Code Corporation CodeXML M2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

2 C003345_01_CodeXML_Modem_Quickstart

C003345_01_CodeXML_Modem_Quickstart 3

Figure 3

Cable Installation

Attach the end of the USB cable to the CodeXML Bluetooth® Modem

(Figure 2). Plug the USB connector into the USB port on the computer

(Figure 3). Once connected the modem’s blue LED light will turn on.

Establish Mode

Scan the USB Mode code (M708_01-right). Scan

the QuickConnect Code again. You are ready to

begin reading bar codes and transmitting decoded

data to the computer.

USB Mode

Keyboard Input (USB & PS2)

The modem is defaulted to English language keyboards. If you need to communicate in a dierent

language requiring a change in keyboard settings, please scan the appropriate code below, after

connecting to the modem:

CodeXML Bluetooth® Modem Installation as a USB Keyboard

Figure 2

USB Cable installed to

CodeXML Bluetooth Modem

Non-printable ASCII

Keyboard (Crtl + character)

Japanese

Non-printable ASCII Keyboard

(No Leading 0)

Change Baud Rate Settings:

Scan the appropriate code below, after connecting to the modem These codes only affect Baud Note:

Rate for the modem and do not aect any settings on Code Readers.

Default Modem

settings:

Baud Rate: 9600

Stop Bits: 8

Parity: None

Stop Bits: 1

Hardware: None

Connecting with QuickConnect Code

(for all cable types):

Scan the QuickConnect Code on the label of the CodeXML Bluetooth®

Modem using the Code Reader with which you wish to establish a paired

connection to a computer. The reader and computer should easily

connect within 10 seconds. The reader will beep once as conﬁ rmation.

If the reader does not connect, the reader will beep four times in rapid

succession.

English (Default)

Universal French

German

19200 38400

57600

115200

1200

2400 4800

9600 (Default)

CodeXML Modem Installatin with PS/2 Cable

Cable Installation

Attach the end of the PS/2 cable with the single connector to

the CodeXML Modem (Figure 2 -page 2). Detach the keyboard

from the computer and connect it to the same type connector on

the PS/2 cable (Figure 8). Connect the other cable end to the

computer (Figure 9). The modem is powered by the PS2 port and

does not require a power supply. Once connected the modem’s

blue LED light will turn on.

Connecting with QuickConnect Code

See instructions on page 2 for establishing a paired connection

between the modem and the computer.

PS/2 Cable installed to CodeXML

Modem & Keyboard

Figure 8

Figure 9

PS2 Mode

Establish Mode

Scan the PS2 Mode code (M660_01-right). You are

ready to begin reading bar codes and transmitting

decoded data

CodeXML Modem Installation with RS-232 (Serial)

Cable Installation

Attach the end of the RS-232 cable to the CodeXML Bluetooth® Modem (Figure 4). Connect the RS-232

adapter to the back of the computer (Figure 5). Connect the RS-232 cable to the power supply (Figure

6). Plug the power supply into a wall socket (Figure 7). Once connected the Modem’s blue LED light will

turn on.

Connecting with QuickConnect Code

See Page 2 for instructions to establish a paired connection between the

Modem and the reader.

Figure 5

Figure 6

Figure 7

Figure 4

RS-232 Cable (Left)

CodeXML Bluetooth Modem

(Center) Power Supply

(Right)

Establish Mode

Scan the RS-232 Mode code (M661_01- right).

Scan the QuickConnect Code again. You are

ready to begin reading bar codes and transmitting

decoded data to a computer.

RS232 Mode

Quickstart Guide

4 C003345_01_CodeXML_Modem_Quickstart

CodeXML M2 Bluetooth® Modem -

Multiple Interface Unit (MIU)

C003345_01_CodeXML_Modem_Quickstart 1

The CodeXML MIU Modem is an external PC accessory designed to be connected

to a computer for use with a Code Reader (CR2 or CR3). The Modem enables

a reader to wirelessly transmit captured data to the computer. The Modem can

accommodate USB, RS-232 (Serial) and PS/2 cables (Figure 1).

Figure 1

The CodeXML MIU Modem is ‘plug & play.’ You simply plug-in the Modem, scan

the QuickConnect code on the Modem Label and start transmitting data from Code

Readers without downloading any drivers or software. The Modem can receive

Bluetooth signals from up to 300 feet (100 meters) away.

For assistance, contact Code Technical Support at: 801 495 2200; or by

email: support@codecorp.com

CodeXML Modem MIU

Modem Firmware Version Output & Values (for reference only):

VVVVvvvvCKP BaudString:

VVVV 4 digit ﬁ rmware version (MSP430 ﬁ rmware version)

vvvv 4 digit ﬁ rmware version (TUSB ﬁ rmware version)

C 1 digit comm mode: 0=PS/2, 1=Serial, 2=Wand Emul., 3=USB

KBD

K Keyboard Map, same as reader host ICD setting 0x2d

P 1 digit packet protocol: 0=Raw, 1=SPX packet, 2=Code Reader

packet

4=Encrypted Packet Format, 5= Protocol Version (AES)

E Pre-emptible Mode

1=enabled, 0=o/disabled

BaudString spx: Baud:DataBitsParityStopbits

For All Readers:

Scan to View

Firmware Version

The radio contained in the CodeXML M2 Bluetooth® Modem has been tested for compliance

with FCC and CE regulations and was found to be compliant with all applicable FCC Rules and

Regulations.

FCC ID#: QQ6-BTR02

Model #: BTHDG-M2-RO-CX

The radio has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment o

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

Any changes made by the user not approved by Code Corporation can void the user’s authority

to operate the equipment.

To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation of 20 cm

or more should be maintained between the antenna of this device and persons during device

operation. To ensure compliance, operations at closer than this distance are not recommended.

The antenna used for this transmitter must not be co-located in conjunction with any other

antenna or transmitter.

CodeXML M2 Bluetooth® Modem

Important Note:

US Patent: US 7,240,831, Patents Pending.

Produkt Specifikationer

Mærke:	Code Corporation
Kategori:	Netværkskort/adapter
Model:	CodeXML M2
Bredde:	69.85 mm
Dybde:	81.28 mm
Højde:	25.4 mm
Produktfarve:	Sort
Driftstemperatur (T-T):	0 - 70 °C
Kabler inkluderet:	PS/2
Bluetooth-version:	2.0+EDR
Forbindelsesteknologi:	Trådløs
Certificering:	CE, FCC
Modemhastighed:	115 Kbit/s
Wi-Fi-bånd:	Enkelt band (2,4 GHz)
LED-indikatorer:	Ja
Udgangsspænding:	5 V
Bæredygtighedscertifikater:	RoHS
Understøttede Windows-operativsystemer:	Ja
Understøttede Mac-operativsystemer:	Ja
Understøttede Linux-operativsystemer:	Ja
Grænseflade:	Bluetooth
Intern:	Ingen
Antenne:	Ja
Maksimal dataoverførselshastighed:	1 Mbit/s
Plug and play:	Ja
Strømforbrug:	100 mA
Maksimal driftstilstand:	10 m
Spread-spectrum-metode:	FHSS
Tilslutning til pc:	Ja