Crestron CLW-DIMFLVEX-P Manual

Crestron Lysdæmper CLW-DIMFLVEX-P

Læs gratis den danske manual til Crestron CLW-DIMFLVEX-P (2 sider) i kategorien Lysdæmper. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om Crestron CLW-DIMFLVEX-P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

CLW-DIMFLVEX-P/CLW-DIMFLVEX-277-P

In-Wall 0–10 V Dimmer

Installation Guide

Description

The Crestron

CLW-DIMFLVEX-P and CLW-DIMFLVEX-277-P are Cameo

in-wall

0–10 V dimmers designed for dimming 0–10 V ballasts or LED drivers, which features

eld-replaceable, engravable buttons. Along with the entire line of Cameo products, they

can be congured with various button layouts and designer colors, making the dimmers

more versatile and affordable than previous generations of in-wall dimmers. Their

streamlined design matches the entire line of Cameo dimmers, switches, and keypads,

making them a great addition to new or retrot installations. In addition to their attractive

look and feel, inNET EX

communications technology brings proven reliability to the

CLW-DIMFLVEX-P and CLW-DIMFLVEX-277-P.

The CLW-DIMFLVEX-P and CLW-DIMFLVEX-277-P are functionally identical. For

simplicity within this guide, the term “CLW-DIMFLVEX-P” is used except where noted.

Installation

WARNING: To avoid re, shock, or death, turn off the power at the circuit breaker or

fuse and test that the power is off before wiring!

CAUTION: Check new installations for short circuits prior to installing a

CLW-DIMFLVEX-P dimmer. With the power off, close the circuit and then restore

power. If the lights do not work, or a breaker trips, check and correct the wiring or

xture (if necessary). Install the dimmer only when the short is no longer present. The

warranty is void if the dimmer is installed and operated with a shorted load.

NOTE: There is no air-gap switch within the unit. Turning the unit off by pressing

bottom button provides a mechanical air-gap. Turning the power off at the breaker

before performing any servicing on lamps is recommended.

NOTE: Observe the following points:

• Install and use this product in accordance with appropriate electrical codes and

regulations.

• A licensed electrician should install this product.

NOTE: Before using the CLW-DIMFLVEX-P, ensure the device is using the latest

rmware. Check for the latest rmware for the CLW-DIMFLVEX-P at

www.crestron.com/rmware. Load the rmware onto the device using Crestron

Toolbox™ software.

NOTE: Multigang installations do not require derating.

Install the CLW-DIMFLVEX-P dimmer.

1. Turn the power off at the circuit breaker.

2. Wire the device as shown in the following diagram.

Additional Resources

Visit the product page on the Crestron

website (www.crestron.com) for

additional information and the latest

rmware updates. Use a QR reader

application on your mobile device to scan

the QR image.

CLW-DIMFLVEX-P CLW-DIMFLVEX-277-P

3. Push all power wires back into the electrical box and fasten the device to the

electrical box with the provided screws.

4. Attach a decorative faceplate.

5. Ensure all buttons, including the program button, actuate without sticking.

6. Restore power at the circuit breaker.

Switched line

Line

Neutral

Ground

From

breaker

0–10 V Ballast

or Driver

Changing Button Assemblies

The button assembly can be removed and replaced with other button assemblies.

1. As shown in the following diagram, remove the button assembly by squeezing the

sides of the bezel near the bezel snaps.

Squeeze at arrow

points and pull to

remove the button

assembly.

NOTE: When the button assembly is removed, power to the unit and load is

removed automatically.

2. Remove button(s) from the front of the button assembly as shown in the following

diagram.

3. Insert new buttons through the front of the bezel and snap into place as shown in

the following diagram. Ensure that the LED strip is on the left side.

4. Attach the button assembly to the device as shown in the following diagram.

Ensure that the LED strip is on the left side.

Gently spread the

frame apart to

remove the buttons.

Gently spread the

frame apart to insert

the buttons.

5. Once power has been restored, press and hold the program button as shown in

the following diagram. After 5 seconds, some LEDs start ashing. Continue to hold

the button and proceed to step 6.

6. While holding the program button, tap all of the buttons in the new layout. The LED

next to the tapped button lights.

NOTE: If the rocker switch is installed, press the top and bottom of the rocker.

7. After all of the buttons have been tapped, release the program button to save the

settings.

NOTE: Changing the button conguration alters the device’s behavior. Refer to

"Default Button Functions" for details.

Step 5:

Press and hold

the program

button.

Step 7:

Release the

program button

to save the

settings.

Step 6:

Tap each of the

installed buttons

on the device.

Operation

NOTE: The device may be warm during operation. This is normal.

The CLW-DIMFLVEX-P is shipped with a rocker switch already installed. In this

conguration, the unit functions as shown below.

NOTE: Operation described in this guide assumes the CLW-DIMFLVEX-P is operating

in Local mode (without the use of a control system). The device can also operate in

Remote mode, in which button behavior is dictated entirely by the control system

program.

LEDs indicate the

load level. When all

loads are off, the

top LED remains

dimly lit to act as a

night light.

Tap to turn the load

on. Press and hold

to raise the light

level.

Tap to turn the load

off. Press and hold

to lower the light

level.

Wire Color

HOT or LINE Black

Neutral White

Ground Green

Switched Line Red

+ Purple

- Gray

SPECIFICATION DETAILS

Load Ratings

Switch Output 5 A

Dimmer Control Output Isolated 0–10 Vdc signal output (60 mA sink/source);

Mechanically latching relay

Dimmed Load Type 0–10 Vdc fluorescent ballast, 0–10 Vdc LED driver

Switched Load Type Incandescent, ELV, MLV, electronic fluorescent

ballast, LED Ballast, HID

Power Requirements

CLW-DIMFLVEX-P

CLW-DIMFLVEX-277-P

120 Vac 50/60 hz

277 Vac 50/60 hz

Environmental

Temperature

Humidity

32° to 104 °F (0° to 40 °C)

10% to 90% RH (noncondensing)

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Lysdæmper
Model:	CLW-DIMFLVEX-P

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron CLW-DIMFLVEX-P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lysdæmper Crestron Manualer

Crestron CM2-DIMUEX Manual

3 December 2025

Crestron CLW-SLVU-P-DA-S Manual

13 August 2025

Crestron CLW-SLVU-P-DSK-T Manual

13 August 2025

Crestron CLW-DIMSWEX-P-DA-S Manual

13 August 2025

Crestron CLW-SLVU-P-A-T Manual

13 August 2025

Crestron CLW-SLVU-P-B-S Manual

13 August 2025

Crestron CLW-SLVU-P-A-S Manual

13 August 2025

Crestron CLW-DIMFLVEX-P-DA Manual

9 Juli 2025

Crestron CLW-DIMUEX-P Manual

9 Juli 2025

Crestron CLW-DELVEX-P Manual

9 Juli 2025

Lysdæmper Manualer

Nyeste Lysdæmper Manualer

Homematic IP HmIP-PDT-A Manual

23 December 2025

Legrand HCL453PMMW Manual

15 December 2025

Legrand RH703PTC Manual

11 December 2025

Legrand LSCL453P Manual

9 December 2025

Legrand RH703PTUW Manual

9 December 2025

Legrand RHL153P Manual

9 December 2025

RADEMACHER DuoFern 9476-1 Manual

17 November 2025

Theben DMG 2 T KNX Manual

9 November 2025

Lutron Caseta P-BDG-PKG1W Manual

7 Oktober 2025

Grässlin trim 300 Manual

27 September 2025