Crestron CLW-DIMFLVEX-P-DA Manual

Crestron Lysdæmper CLW-DIMFLVEX-P-DA

Læs gratis den danske manual til Crestron CLW-DIMFLVEX-P-DA (2 sider) i kategorien Lysdæmper. Denne vejledning er vurderet som hjælpsom af 4 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 2.5 anmeldelser. Har du et spørgsmål om Crestron CLW-DIMFLVEX-P-DA, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
CLW-DIMFLVEX-P/CLW-DIMFLVEX-277-P
In-Wall 0–10 V Dimmer
Installation Guide
Description
The Crestron
®
CLW-DIMFLVEX-P and CLW-DIMFLVEX-277-P are Cameo
®
in-wall
eld-replaceable, engravable buttons. Along with the entire line of Cameo products, they
can be congured with various button layouts and designer colors, making the dimmers
more versatile and affordable than previous generations of in-wall dimmers. Their
streamlined design matches the entire line of Cameo dimmers, switches, and keypads,
making them a great addition to new or retrot installations. In addition to their attractive
look and feel, inNET EX
®
communications technology brings proven reliability to the
CLW-DIMFLVEX-P and CLW-DIMFLVEX-277-P.
The CLW-DIMFLVEX-P and CLW-DIMFLVEX-277-P are functionally identical. For
simplicity within this guide, the term “CLW-DIMFLVEX-P” is used except where noted.
Installation
WARNING: To avoid re, shock, or death, turn off the power at the circuit breaker or
fuse and test that the power is off before wiring!
CAUTION: Check new installations for short circuits prior to installing a
CLW-DIMFLVEX-P dimmer. With the power off, close the circuit and then restore
power. If the lights do not work, or a breaker trips, check and correct the wiring or
xture (if necessary). Install the dimmer only when the short is no longer present. The
warranty is void if the dimmer is installed and operated with a shorted load.
NOTE: There is no air-gap switch within the unit. Turning the unit off by pressing
bottom button provides a mechanical air-gap. Turning the power off at the breaker
before performing any servicing on lamps is recommended.
NOTE: Observe the following points:
• Install and use this product in accordance with appropriate electrical codes and
regulations.
• A licensed electrician should install this product.
NOTE: Before using the CLW-DIMFLVEX-P, ensure the device is using the latest
rmware. Check for the latest rmware for the CLW-DIMFLVEX-P at
www.crestron.com/rmware. Load the rmware onto the device using Crestron
Toolbox™ software.
NOTE: Multigang installations do not require derating.
Install the CLW-DIMFLVEX-P dimmer.
1. Turn the power off at the circuit breaker.
2. Wire the device as shown in the following diagram.
Additional Resources
Visit the product page on the Crestron
website (www.crestron.com) for
additional information and the latest
rmware updates. Use a QR reader
application on your mobile device to scan
the QR image.
CLW-DIMFLVEX-P CLW-DIMFLVEX-277-P
3. Push all power wires back into the electrical box and fasten the device to the
electrical box with the provided screws.
4. Attach a decorative faceplate.
5. Ensure all buttons, including the program button, actuate without sticking.
6. Restore power at the circuit breaker.
Switched line
Line
Neutral
Ground
From
breaker
+
0–10 V Ballast
or Driver
-
Changing Button Assemblies
The button assembly can be removed and replaced with other button assemblies.
1. As shown in the following diagram, remove the button assembly by squeezing the
sides of the bezel near the bezel snaps.
Squeeze at arrow
points and pull to
remove the button
assembly.
NOTE: When the button assembly is removed, power to the unit and load is
removed automatically.
2. Remove button(s) from the front of the button assembly as shown in the following
diagram.
3. Insert new buttons through the front of the bezel and snap into place as shown in
the following diagram. Ensure that the LED strip is on the left side.
4. Attach the button assembly to the device as shown in the following diagram.
Ensure that the LED strip is on the left side.
Gently spread the
frame apart to
remove the buttons.
Gently spread the
frame apart to insert
the buttons.
5. Once power has been restored, press and hold the program button as shown in
the following diagram. After 5 seconds, some LEDs start ashing. Continue to hold
the button and proceed to step 6.
6. While holding the program button, tap all of the buttons in the new layout. The LED
next to the tapped button lights.
NOTE: If the rocker switch is installed, press the top and bottom of the rocker.
7. After all of the buttons have been tapped, release the program button to save the
settings.
NOTE: Changing the button conguration alters the device’s behavior. Refer to
"Default Button Functions" for details.
Step 5:
Press and hold
the program
button.
Step 7:
Release the
program button
to save the
settings.
Step 6:
Tap each of the
installed buttons
on the device.
Operation
NOTE: The device may be warm during operation. This is normal.
The CLW-DIMFLVEX-P is shipped with a rocker switch already installed. In this
conguration, the unit functions as shown below.
NOTE: Operation described in this guide assumes the CLW-DIMFLVEX-P is operating
in Local mode (without the use of a control system). The device can also operate in
Remote mode, in which button behavior is dictated entirely by the control system
program.
LEDs indicate the
load level. When all
loads are off, the
top LED remains
dimly lit to act as a
night light.
Tap to turn the load
on. Press and hold
to raise the light
level.
Tap to turn the load
off. Press and hold
to lower the light
level.
Wire Color
HOT or LINE Black
Neutral White
Ground Green
Switched Line Red
+ Purple
- Gray
SPECIFICATION DETAILS
Load Ratings
Switch Output 5 A
Dimmer Control Output Isolated 0–10 Vdc signal output (60 mA sink/source);
Mechanically latching relay
Dimmed Load Type 0–10 Vdc fluorescent ballast, 0–10 Vdc LED driver
Switched Load Type Incandescent, ELV, MLV, electronic fluorescent
ballast, LED Ballast, HID
Power Requirements
CLW-DIMFLVEX-P
CLW-DIMFLVEX-277-P
120 Vac 50/60 hz
277 Vac 50/60 hz
Environmental
Temperature
Humidity
32° to 104 °F (0° to 40 °C)
10% to 90% RH (noncondensing)
Full On
Fast Off
Full On
Full On
Full On
Full On
Fast Off
Full On
Full On
Fast Off
Fast Off
Full On
Full On
Raise
Lower
Raise
Lower
Raise
Lower
Raise
Lower
Raise
Lower
Lower
Raise
Button Hold (Hold more than 1/2 second.)
Button Double Tap (Tap twice within 1/2 second.)
Default Button Functions
The gures below illustrate the default functions available for each physical button
conguration and tap- or hold-actuation sequence.
Button Tap
Off
Preset 1
Toggle
Raise
Lower
Preset 1
Preset 2
Preset 3
Off
Preset 1
Toggle
Raise
Lower
Preset 1
Off
Off
Preset 1
Preset 2
Preset 1
This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories
Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters
Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
CAUTION: Changes or modications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
Wireless Communications
The device connects to the Crestron network via the inNET EX communications
protocol. Use the procedures outlined below to join or leave an inNET EX network and
to verify communications between the device and the control system.
Joining an inNET EX Network
Before a device can be used in a lighting system, it must rst join an inNET EX network.
To join an inNET EX network, the device must be acquired by an inNET EX gateway.
NOTE: A device can be acquired by only one gateway.
1. Put the inNET EX gateway into Acquire mode from the unit itself or from Crestron
Toolbox. Refer to the gateway’s manual at www.crestron.com/manuals for details.
NOTE: In an environment where multiple gateways are installed, only one
gateway should be in Acquire mode at any time.
2. Put the device into Acquire mode:
a. Tap the top button three times and then press and hold it down
(tap-tap-tap-press+hold) until the top LEDs on the device blink once (this can
take up to 10 seconds).
b. Release the button to start the acquire process. The top LED blinks slowly to
show that the device is actively scanning the inNET EX network.
• The top two LEDs turn on for 5 seconds to show that the device has been
successfully acquired by the infiNET EX network.
• The top LED blinks fast to indicate that the device was not successfully
acquired by the infiNET EX network. Tap the top button to acknowledge the
failure. Ensure the gateway is in Acquire mode and within range before
attempting the acquire process again.
3. Once all devices have been acquired, take the gateway out of Acquire mode. Refer
to the gateway’s manual for details.
Leaving an inNET EX Network
To leave an inNET EX network, put the device into Acquire mode, as described in
“Joining an inNET EX Network” above, when no gateway is in Acquire mode.
Verifying Communications Status
To check the communications status of the device, tap the top button three times and
then press and hold it down (tap-tap-tap-press+hold) for up to 2 seconds. The LED
blinks to indicate the communications status. Refer to the following table for details.
Troubleshooting
The following table provides corrective actions for possible trouble situations. If further
assistance is required, please contact a Crestron customer service representative.
Crestron Electronics, Inc. Installation Guide - DOC. 7831A
15 Volvo Drive Rockleigh, NJ 07647 (2046056)
Tel: 888.CRESTRON 10.16
Fax: 201.767.7576 Specications subject to
www.crestron.com change without notice.
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The product warranty can be found at www.crestron.com/warranty.
The specic patents that cover Crestron products are listed at patents.crestron.com.
Certain Crestron products contain open source software. For specic information, please visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Cameo, Crestron Toolbox, inNET EX and the inNET EX logo are either
trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. UL and the UL logo are either trademarks or registered trademarks of Underwriters
Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Crestron disclaims any proprietary interest in the marks and names of others.
Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2016 Crestron Electronics, Inc.
LED COMMUNICATIONS STATUS
Turns on for 5 seconds The device is communicating with the control system.
Blinks three times The device is communicating with the gateway but the
gateway is not communicating with the control system.
Blinks twice The device was previously joined to the network but is
not communicating with the gateway.
Blinks once The device is not joined to the network.
The CLW-DIMFLVEX-P can recall and store up to three presets depending on the
installed button conguration.
Set a preset level:
1. Adjust the light level to the desired level.
2. Enter Programming mode by quickly tapping the program button as shown below.
Buttons that are capable of storing a preset ash their LEDs.
3. Press and hold the desired preset button until the LED blinks (approximately 2
seconds). Release the button to store the new level.
If a button is not pressed, the device exits the Programming mode after approximately 5
seconds.
NOTE: Programming mode is disabled when the load is off.
NOTE: A delayed off can be added via control system programming.
Preset 1
Preset 2
Preset 3
Off
Step 3:
Hold the button
to store a new
level.
Step 2:
Quickly tap the
program button.
LEDs ash to indicate
the buttons that can
be programmed.
TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION
An LED is constantly
blinking and the dimmable
load stays at a low level.
The purple and gray wires
are shorted together.
Check the wiring.
An LED is constantly
blinking.
The purple and gray wires
are shorted together.
Check the wiring.
NOTE: LEDs extinguish
when the load is turned
off.
The dimmable load does
not dim.
The purple or gray wire is
not connected.
Verify the wiring.

Produkt Specifikationer

Mærke: Crestron
Kategori: Lysdæmper
Model: CLW-DIMFLVEX-P-DA

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron CLW-DIMFLVEX-P-DA stil et spørgsmål nedenfor, og andre brugere vil svare dig


Lysdæmper Crestron Manualer

Crestron

Crestron CLW-DIMFLVEX-P-DA Manual

9 Juli 2025
Crestron

Crestron CLW-DIMUEX-P Manual

9 Juli 2025
Crestron

Crestron CLW-DELVEX-P Manual

9 Juli 2025
Crestron

Crestron CLWI-DIMUNEX Manual

9 Juli 2025
Crestron

Crestron CLF-LDIMUEX Manual

9 Juli 2025
Crestron

Crestron CLWI-DIMFLVEX Manual

6 Juli 2025
Crestron

Crestron CLW-DIMEX-P Manual

2 April 2025
Crestron

Crestron CLW-DIMFLVEX-P Manual

12 Marts 2025

Lysdæmper Manualer

Nyeste Lysdæmper Manualer

Legrand

Legrand ADTHRRG1 Manual

7 Juli 2025
Legrand

Legrand ADTPRRG1 Manual

7 Juli 2025
Liteline

Liteline LC-CRTL-3WAY-1 Manual

18 Juni 2025
Liteline

Liteline LC-CRTL-DIM-1 Manual

17 Juni 2025
InterBar

InterBar 8010 Manual

29 Januar 2025
Vimar

Vimar 20175 Manual

15 December 2024
Vimar

Vimar 19147 Manual

15 December 2024
Vimar

Vimar 19595.0 Manual

15 December 2024
Vimar

Vimar 16603.120.B Manual

15 December 2024
Vimar

Vimar 16604 Manual

15 December 2024