Delta Dore Tyxia 611 Manual

Delta Dore Lettelse Tyxia 611

Læs gratis den danske manual til Delta Dore Tyxia 611 (1 sider) i kategorien Lettelse. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Delta Dore Tyxia 611, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

The TYXIA 611 pack enables

you to create a two-way lighng

without an exisng switch.

Recommendaons

IMPORTANT: the control wires are not

insulated from the mains power supply.

All connected equipment must be marked CE

and meet the requirements of the low voltage

devices as well as assembly recommendaons.

Local control wires can be extended up to 10

m (separate from the 230 V).

10A circuit breaker required.

Step 1 - Install your products

230V~

OFF

You can install the lighng receiver in a ﬂush-mounted

box, behind a switch or control push-buon

(automac detecon on use) or behind a ceiling.

1.1 Connecon instrucons for terminals 1 2 3 4.

Strip the wires while respecng the strip length speciﬁed on the product.

1.1.1 Solid wires 1.1.2 Stranded wires

Push the wire fully

into the terminal.

Removal recommendaons

- Switch oﬀ the power supply.

- Use the tool supplied or a 2.5 mm screwdriver

to press the buon of the front terminal before

removing the wire. 2

1.2 Connecon instrucons for IN1 - COM - IN2 terminals

Use the wires supplied.

Push the wire fully into the terminal.

1.3 TYXIA 5610 connecon

Connect:

The light to terminals 3 and 4.

The switch to the IN1 -

COM terminals (input 1).

The 230 V power supply to terminals 1

and 2.

Switch the installaon power back on to

connue with the associaon operaon.

1.4 TYXIA 2310 installaon

This unit must not be placed on a metal surface.

Conﬁguraon buons

Step 2 - Determine the operang mode of the TYXIA 2310

The operang mode of the TYXIA 2310 is, by default, mode A, i.e. for control-

ling 2 ON/OFF lighng channels.

IMPORTANT: If you approve this selecon, go directly to step 3,

'Associate your products'.

Otherwise, determine the operang mode suited to your installaon.

Mode B: Scenario mode to simultaneously control diﬀerent receivers.

Mode C: Dimmer mode to control a dimmer lighng channel.

Open the unit.

Press the T2 buon several mes to select

your desired operang mode.

...... ...

EXIT

ON/OFF

... ... ...

Mode A Mode B Mode C

The LED ﬂ ashes

once

The LED ﬂ ashes

twice

The LED ﬂ ashes

three  mes

Step 3 - Associate your products

❶Set the TYXIA 5610 receiver to associaon

standby mode. Press and hold the buon for 3

seconds unl the LED ﬂashes, release.

❷ On the TYXIA 2310 emiers, send the

associaon order: Mode A or B: Press the

buon of the channel you want to associate

for 3 seconds (1 or 2).

Mode C: Press the 1 and 2 buons

at the same me and hold for 3 seconds.

❸ When the receiver LED has stopped ﬂashing.

The products are now associated.

Number of associated emiers: 16 maximum

Troubleshoong

Summary of funcons accessible using the receiver buon

3’’

>10’’ 20’’>

Associaon/

Conﬁguraon

Removing an

associaon

Removing

all associaons

Press and hold the buon for x seconds

AAssociaon/Conﬁguraon

Press the receiver buon for 3 seconds unl the LED ﬂashes, release.

BRemove an associaon

On the TYXIA 5610 receiver:

Press the receiver buon for 10 seconds unl the LED ﬂashes rapidly, release.

On the TYXIA 2310 emier:

Mode A or B: Press the buon of the channel you want to delete for 3 seconds

(1 or 2).

Mode C: Press the 1 and 2 buons at the same me and hold for 3 seconds.

CRemove all associaons

Press the receiver's buon for 20 seconds.

Press and hold unl the LED switches oﬀ aer the rapid ﬂashing phase, release.

The receiver has no wireless connecon.

The receiver locks in oﬀ mode

When an overload is detected, the product locks in oﬀ mode for 30 seconds be-

fore authorising a new acvaon. The LED ﬂashes rapidly throughout this phase.

To exit the receiver from this secure mode, replace the bulb connected by a bulb

with lower power (refer to compability table).

You wish to change the operang mode of a product which has already been

associated. - You must ﬁrst delete any associaon.

Replacing the baeries

Red Red Red

The red LED ﬂashes each me you press = Baery fault

Compability

① 230 V halogen or 230 V incandescent bulbs.

② 230V energy-saving compact ﬂ uorescent bulbs.

③ 230V LED bulbs.

④ Very low voltage 12V halogen or LED bulbs with AC or DC electronic

transformer.

⑤Very low voltage 12V halogen bulbs with ferromagne c or toroidal transformer.

⑥Fluorescent tube.

200 W 100 W 100 W100 W100 W

LEDLED

150 W 100 W

Hi-Fi

230 V~ 50 Hz

230 V~

IN1

COM

TYXIA

5610

1 2 3 4

230V~

200W max

1234

Standby 0.06W

230 V~ 0.6 VA

IN1

CO M

IN1

CO M

OFF

230V~

N S1NL

7mm 0,5 mm

KY31A02

123 4

230V

Technical characteriscs

TYXIA 5610

- Power supply 230 V~ 0.6 VA

- Class II insulaon

Stand-by consumpon: 0.06 W

- Storage temperature: -10 °C / +70 °C

- Operang temperature: -10 °C / +40 °C

- IP 40 (ﬂush mounng box)

- Dimensions: 41 x 36 x 14.5 mm

- X3D wireless remote control device:

868.7 MHz to 869.2 MHz

- Maximum wireless power < 10 mW Category 2 receiver

TYXIA 2310

- CR 2430 lithium baery power supply (included),

Baery life 10 years depending on use

- Storage temperature: -10 °C / +70 °C

- Operang temperature: -10 °C / +40 °C

- IP 40 - IK 04

- Dimensions: 84 x 84 x 13 mm

- X3D wireless remote control device:

868.7 MHz to 869.2 MHz

- Maximum wireless power < 10 mW Category 2 receiver

EN Wireless two-way pack

Use an electrically

isolated tool to per-

form the acons on

the receiver conﬁgu-

raon buon.

TYXIA

Switch oﬀ the installaon

power supply.

Do not strip the wires when they are

connected to the product as you

could damage the internal connector.

1 2 3 4

TYXIA

5610

TYXIA

5610

... ... ...

> 3s

N S1NL

1 2 3 4

TYXIA

5610

OFF

N S1NL

>3s

Removal recommendaons

Turn the wire while pulling on it.

123 4

TYXIA 2310

TYXIA 5610

On / Off

Alim. 230 V

230 V

200 W maxi.

TYXIA 611 pack

Using the tool

supplied or a 2.5

mm screwdriver,

press the terminal

buon then insert

the wire.

Important : If you have selected opera ng mode B (scenario

control), set each item to the required state (e.g. shu ers

lowered, ligh ng oﬀ ) before moving on to stage 1.

Produkt Specifikationer

Mærke:	Delta Dore
Kategori:	Lettelse
Model:	Tyxia 611

Har du brug for hjælp?

Hvis du har brug for hjælp til Delta Dore Tyxia 611 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lettelse Delta Dore Manualer

Delta Dore Easy Bulb GU10CW Manual

16 August 2024

Delta Dore Tyxia 611 Manual

13 August 2024

Delta Dore Tyxia 620 Manual

12 August 2024

Delta Dore Tyxia 511 Manual

11 August 2024

Delta Dore Easy Bulb E14CW Manual

10 August 2024

Delta Dore Easy Bulb E27CW Manual

10 August 2024

Delta Dore Easy Plug G13EM Manual

9 August 2024

Delta Dore Tyxia 6610 Manual

8 August 2024

Delta Dore Tyxia 501 Manual

6 August 2024

Lettelse Manualer

Nyeste Lettelse Manualer

Dainolite V166-1W Manual

5 April 2025

Dainolite OFE-161P Manual

5 April 2025

Dainolite DMLED10-A-5D Manual

5 April 2025

Dainolite DM1958F Manual

5 April 2025

NUVO Ballerina 60/1265 Manual

4 April 2025

NUVO SF77/196 Manual

4 April 2025

NUVO Ballerina 60/329 Manual

4 April 2025

NUVO Cordello 60/7883 Manual

4 April 2025

NUVO Destin 60/7706 Manual

4 April 2025

NUVO Livingston 60/7669 Manual

4 April 2025