Electro Harmonix Bass Metaphors Manual

Electro Harmonix Ikke kategoriseret Bass Metaphors

Læs gratis den danske manual til Electro Harmonix Bass Metaphors (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Electro Harmonix Bass Metaphors, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

BASS METAPHORS

Channel Strip and Over Drive for Bass Players

Congratulations on your purchase of the Electro-Harmonix XO Bass

Metaphors. The Bass Metaphors is a uniquely designed multi-effect unit that

combines a preamp, EQ and overdrive. All are laid out in a channel strip

configuration. Additionally, a compressor may be independently assigned through a

toggle switch. The Bass Metaphors was designed and voiced specifically for bass

players. The parallel arrangement of the effects allows for finely tuned control over

each element in order to give you a final tone that fits your style and needs.

The Preamp section is made up of a Dry channel, EQ channel and a Distortion

channel. Each channel has its own level control, appropriately labeled. The EQ

channel has further controls, which adjust Bass and Treble independently. The

Distortion channel is also footswitch accessible, allowing the user to preset a sound to

be cut in or out as needed. The Volume control functions as a master volume after

the effects.

In addition, a leveling compressor can be cut into the circuit before the output, to

add sustain, “punch” or to even out your performance. This is controlled by the

“Squash” setting of the toggle switch placed in the center of the case.

The output of the Bass Metaphor is balanced/unbalanced and conveniently accessed

by ¼” TRS jack and by a standard XLR on the side of the unit. Please note that using

a standard ¼” unbalanced plug will bypass the balanced output for BOTH

connectors.

Effect Engaged LED – On when the effect is active and off when not used.

Distortion Engaged LED – The LED is on when the distortion is active and off

when the distortion is not in use.

DRY Out – The dry output knob allows you to vary the amount of the dry signal

heard at the output.

EQ level– Is the adjustable level of how much equalization is inserted into the

channel strip. When the EQ is fully down (counterclockwise) there is no EQ in the

channel strip. As the knob is rotated clockwise the more the amount of the set treble

and bass knobs will be added. At the full clockwise position the full amount of

potential EQ is applied.

Treble – The treble knob controls the amount of the 2-pole treble filter that is added

to the signal. When turned fully counterclockwise, there is no added treble. As the

knob is advanced clockwise, a carefully selected treble frequency is applied whose

amount linearly rises to the end of the clockwise rotation.

Bass – The bass knob controls the amount of bass frequency that is added to the

signal. When turned fully counterclockwise, there is no added bass. As the knob is

advanced clockwise, a carefully selected bass frequency is applied whose amount

linearly rises to the end of the clockwise rotation. It is also a 2-pole filter.

Note: When Bass filter is combined with the Treble filter you have a 4-pole filter.

Scooped midranges to very subtle to overt sonic possibilities can be found. This is a

very colorful EQ.

Direct output- signal is connected directly to the input for access of the original

signal.

Distortion – Controls the amount of distortion that is introduced into the channel

strip.

Volume – Controls the master volume of the output signal.

¼” INPUT – Input jack for your bass guitar or instrument.

Direct Out – Your signal is assigned to this pass through output providing you with a

dry signal only.

¼” OUTPUT –Balanced/unbalanced tip ring sleeve balanced ¼ inch output

connector. This jack will accept both a balanced or unbalanced signal.

XLR OUTPUT – 3-pin connector allowing a balanced signal to be sent to low

impedance XLR input. IE to a recording console, live mix console or any high end

balanced processor.

WARNING: Use only the US96DC-200BI adapter that the Bass Metaphors comes

supplied with. Do not use any other AC adapters. Using other AC adapters with the

incorrect rating, even those made by Electro-Harmonix, could cause harm to the unit,

the adapter or you. The SMMH does not use batteries.

Produkt Specifikationer

Mærke:	Electro Harmonix
Kategori:	Ikke kategoriseret
Model:	Bass Metaphors

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro Harmonix Bass Metaphors stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Electro Harmonix Manualer

Electro Harmonix J Mascis Ram's Head Manual

8 Oktober 2025

Electro Harmonix Anniversary Big Muff Pi Manual

6 Oktober 2025

Electro Harmonix Grand Canyon Manual

6 Oktober 2025

Electro Harmonix Doctor Q Manual

6 Oktober 2025

Electro Harmonix Stereo Memory Man with Hazarai Manual

6 Oktober 2025

Electro Harmonix Next Step Volume Pedal Manual

5 Oktober 2025

Electro Harmonix 8-Step Program Manual

28 September 2025

Electro Harmonix Lizard King Manual

7 September 2025

Electro Harmonix Holy Grail Neo Manual

5 August 2025

Electro Harmonix Pico Rerun Manual

5 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Microchip PIC18F2620 Manual

25 Oktober 2025

Microchip RN240 Manual

24 Oktober 2025

Jane BLW Manual

24 Oktober 2025

Kanto PS200 Manual

24 Oktober 2025

Microchip PIC24HJ12GP201 Manual

24 Oktober 2025

Microchip TC4420 Manual

24 Oktober 2025

Calor Pure Force 3en1 DT8765 Manual

24 Oktober 2025

Hikvision DS-QAE1A40G1-VB Manual

23 Oktober 2025

Microchip HV2818 Manual

23 Oktober 2025

Microchip MIC2298 Manual

23 Oktober 2025