Electro Harmonix Micro Metal Muff Manual
Electro Harmonix
Ikke kategoriseret
Micro Metal Muff
Læs nedenfor 📖 manual på dansk for Electro Harmonix Micro Metal Muff (4 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 26 personer og blev bedømt med 3.7 stjerner i gennemsnit af 13.5 brugere
Side 1/4
MICRO METAL MUFF
- DESCRIPTION -
Congratulations on your purchase of the MICRO METAL MUFF! Electro-
Harmonix gave you an instant classic in the Metal Muff with Top Boost. The
MICRO METAL MUFF offers the same heavy metal sound in a smaller, easier
to use package.
- CONTROLS -
VOLUME CONTROL – sets the output level.
TONE CONTROL – provides up to 15dB of cut and boost in the middle
frequency range.
DISTORTION CONTROL – adjusts the amount of input gain.
TOP BOOST TOGGLE SWITCH – provides two settings for an extra ‘bite’
by boosting a narrow band of high frequencies. In the down position a low
amount of Top Boost is engaged. In the up position a high amount of Top
Boost is engaged. In the middle position no Top Boost is engaged.
FOOTSWITCH – Selects whether the MICRO METAL MUFF is engaged or in
buffered bypassed. The corresponding LED will be lit when the pedal is
engaged, and dark when bypassed.
INPUT Jack – This ¼” jack is the audio input to the MICRO METAL MUFF.
OUTPUT Jack – ICRO METAL This ¼” jack is the audio output from the M
MUFF. When the MICRO METAL MUFF is in Bypass mode, the OUTPUT jack
is connected to the INPUT jack through a buffer.
- OPERATION AND WARNINGS -
Power, from the internal 9-volt battery or external battery eliminator, is
activated by plugging into the input. The input cable should be removed
when the unit is not in use to avoid running down the battery. The input
impedance presented at the Input Jack is 1Mohm. The output impedance at
the Output Jack is 600 ohms.
The barrel connector on the front of the MICRO METAL MUFF is for a 9-volt
battery eliminator capable of delivering 100 mA of current. The inner ring of
the 9-volt battery eliminator must be negative, the outer ring positive. The
unit’s battery may be left in or taken out when the eliminator is in use.
To achieve its biting distortion, the MICRO METAL MUFF has very high
maximum gain. This requires that both the pickups and cables be well
shielded and properly grounded to avoid excessive hum when high sustain
control settings are used.
To change the 9-volt battery, you must remove the 4 screws on the bottom
of the MICRO METAL MUFF. Once the screws are removed, you can take off
the bottom plate and change the battery. Please do not touch the circuit
board while the bottom plate is off or you may damage a component.
The optional 9V power supply from Electro-Harmonix is US96DC-200BI
(same as used by Boss ™ & Ibanez™) 9.6 volts/DC 200ma. The barrel
connector on the front of the MICRO METAL MUFF is for the 9-volt battery
eliminator capable of delivering 100 mA of current. The inner ring of the 9-
volt battery eliminator must be negative, the outer ring positive. The unit’s
battery may be left in or taken out when the eliminator is in use.
Produkt Specifikationer
| Mærke: | Electro Harmonix |
| Kategori: | Ikke kategoriseret |
| Model: | Micro Metal Muff |
Har du brug for hjælp?
Hvis du har brug for hjælp til Electro Harmonix Micro Metal Muff stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ikke kategoriseret Electro Harmonix Manualer
1 Januar 2025
29 December 2024
29 December 2024
29 December 2024
4 December 2024
18 November 2024
11 Oktober 2024
4 September 2024
4 September 2024
3 September 2024
Ikke kategoriseret Manualer
- Ikke kategoriseret AJ.BA
- Ikke kategoriseret Riello
- Ikke kategoriseret Be Cool
- Ikke kategoriseret Privileg
- Ikke kategoriseret Noris
- Ikke kategoriseret Greisinger
- Ikke kategoriseret Thermaltake
- Ikke kategoriseret Duracell
- Ikke kategoriseret Fontiso
- Ikke kategoriseret Infiniton
- Ikke kategoriseret Sole Fitness
- Ikke kategoriseret Sharper Image
- Ikke kategoriseret Innr
- Ikke kategoriseret Austral
- Ikke kategoriseret Sunset
Nyeste Ikke kategoriseret Manualer
1 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025
1 Juni 2025