Electro Harmonix Nano Looper 360 Manual


Læs gratis den danske manual til Electro Harmonix Nano Looper 360 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Electro Harmonix Nano Looper 360, eller vil du spørge andre brugere om produktet?

Side 1/4
1
NANO LOOPER 360
Compact Looper
Congratulations on your purchase of the Nano Looper 360 The Nano Looper 360 is ! a
small, extremely easy to use looper with a total of -seconds of loop recording time. Not 360
only that, the available 360 seconds can be divided into 11 different Loops, so you get the
most out of the available memory! You can think of the Nano Looper 360 as your very own
Loop Locker.
WARNING: Your Nano Looper 360 comes equipped with an Electro-Harmonix 9.6DC-
200BI power supply (same as used by Boss® & Ibanez®: 9.6 Volts DC 200mA). The Nano
Looper 360 requires 90mA at 9VDC with a center negative plug. Using the wrong adapter
or plug polarity may damage your unit and void the warranty.
– – FEATURES
- 6 minutes of loop recording time
- selectable independent Loops 11 , , that remain in memory until you erase them
- High quality uncompressed audio: -bit A/D/A, 44.1k Sample Rate , 24 Hz
- Intuitive looping interface
- Undo-Redo function
- Unlimited overdubbing
- Small pedal board footprint
- AC Adapter Included
- tionally may use 9V Alkaline Battery, battery life: approximately 4 hours of operation Op
(varies on conditions of use)
– – CONTROLS
LEVEL Knob Controls the output level of the Loop. Your dry signal remains at unity
signal level from input to output. The dry signal also remains analog throughout the . 360
LOOP Knob Selects number: 1-11. When scrolling through loops, the Loop MEM LED
flash quickly during transitions. If the loop has no recorded memory, the es MEM LED
remains off. If the loop has recorded memory, the remains and playback can MEM LED on
begin.
INPUT Jack Nano Looper 360. The input This ¼” jack is the audio input for the
impedance is 2.2M .
OUTPUT Jack Nano Looper 360. The output This ¼” jack is the audio output from the
impedance is 470.
9V Power Jack Plug the output of the supplied AC adapter into the 9V power jack
located at the top of the Nano Looper 360. The Nano Looper 360 draws mA at 9VDC 90
with a center negative plug. The Nano Looper 360 accepts Boss® and Ibanez® style AC
Adapters.
2
– – QUICK START GUIDE
RECORDING A LOOP
1. To record a Loop; simply select an empty bank and press the once. The Footswitch
REC LED will light solid and recording begins immediately.
2. To stop recording the l press the again once. The will turn oop, Footswitch REC LED
off, the will turn on, and the loop will begin playing immediately. The PLAY LED
MEM LED will also light solid, indicating the presence of recorded loop memory.
3. All Loops play indefinitely. Each time the loop repeats, the will turn off PLAY LED
briefly.
4. After a loop is recorded, the length is subtracted from the total loop recording time.
5. Note: if the full 360 seconds of Loop Recording time is reached, recording will stop
automatically. The will turn off, the will turn on, and the Loop REC LED PLAY LED
will begin playing immediately. The will also light solid, indicating the MEM LED
presence of recorded l memory. oop
STOPPING & STARTING LOOP PLAYBACK
1. To stop loop playback, press the two times quickly. Footswitch
2. Note: REC LED the will turn on together with the during the first press. PLAY LED
Both LEDs turn off during the second press and playback stops immediately.
3. While stopped, press and release the Footswitch once to start playback. The PLAY
LED will light indicating the loop is playing.
RECORDING AN OVERDUB
1. To record an overdub, make sure a L is playing back. If a loop is not playingoop ,
press the once to begin playback. The will turn on and the Footswitch PLAY LED
loop will begin playing immediately.
2. To start recording an overdub, press the once. The will turn Footswitch REC LED
on, together with the , and audio will be recorded on top of the original PLAY LED
loop. No volume loss will occur to the previously recorded portion of the loop.
3. To stop overdubbing the loop; press the again once. The will Footswitch REC LED
turn off, and the loop will continue playing along with the overdubbed audio.
4. Overdubbing will never change the length of the loop.
5. If the loop repeats during overdubbing, the and will both turn REC LED PLAY LED
off briefly. The Nano Looper 360 can overdub indefinitely, allowing you to
continuously overdub new audio onto your loop.
6. After finishing an Overdub, the UNDO-REDO function is enabled. You may undo,
then redo the last Overdub as many times as you like.
UNDO-REDO FUNCTION
1. The Undo/Redo function can only be initiated while a loop is playing back. Undo/Redo
cannot be performed during Overdub, Record or Stop modes.
2. To undo an overdub (remove the last take) during l playback, press and hold the oop
Footswitch for 1-second. The PLAY LED will blink twice and the previous overdub
will be removed.
3. To redo an overdub (restore the last take) during l playback, press and hold the oop
Footswitch for 1-second. The PLAY LED will blink twice and the previous overdub
will be restored.


Produkt Specifikationer

Mærke: Electro Harmonix
Kategori: Ikke kategoriseret
Model: Nano Looper 360

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro Harmonix Nano Looper 360 stil et spørgsmål nedenfor, og andre brugere vil svare dig