Electro Harmonix Oceans 11 Manual


Læs gratis den danske manual til Electro Harmonix Oceans 11 (16 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Electro Harmonix Oceans 11, eller vil du spørge andre brugere om produktet?

Side 1/16
1
OCEANS 11
Multifunction Digital Reverb
Congratulations on your purchase of the Electro-Harmonix OCEANS 11
Reverb, the compact digital reverb pedal that does it all. Splash your tone
with subtle ambience using classic Hall and Plate, or drench your guitar in
surreal soundscapes with Shimmer and Modulation. A newly developed
Spring algorithm faithfully emulates the iconic drip of vintage Fender ®
reverb units. Unique and powerful polyphonic, dynamic, and auto-
triggering reverbs inspire radical experimentation. Instantaneous control
of infinite reverb unleashes a torrent of sonic possibilities for a truly
unparalleled reverb experience.
- TABLE OF CONTENTS -
Getting started with OCEANS 11 2
Connections 2
Controls 2
Descriptions of Reverb Types 4
Mode Button Functionality 5
Footswitch Functionality 7
Summary Chart 8
Secondary Knob Functionality 10
Infinite Reverb Functionality 14
Warranty Information and FCC Compliance 16
2
- GETTING STARTED WITH OCEANS 11 -
1. Plug the supplied EHX9.6DC AC Adapter into the jack at the top of the
OCEANS 11.
2. Plug your guitar into the INPUT jack and plug the OUTPUT jack into
your amplifier.
3. Turn the 11-position Reverb Type knob to the HALL setting for a
classic warm reverb.
4. Set the decay time using the TIME knob, the reverb tone with the
TONE knob, and the reverb volume with the FX LVL knob.
- CONNECTIONS -
INPUT Jack This ¼” jack is the audio input of the OCEANS 11. The
input impedance is . 1M
OUTPUT Jack This ¼” jack is the audio output of the OCEANS 11. The
output impedance is 680 .
INFINITE Jack – Connect an external momentary footswitch to this ¼”
jack. Press and hold the external switch to activate infinite reverb. The
infinite reverb wash will continue as long as the external switch is pressed.
The external switch should be normally open. Upon engaging the switch,
it should create a short circuit between the Tip and Sleeve of the plug.
See “Infinite Reverb ” on page Functionality 14 for details on using infinite
reverb.
9V Power Jack Plug the output of the OCEANS 11’s supplied EHX9.6DC
200mA AC adapter in the 9V power jack located at the top of the pedal.
The OCEANS 11 requires 150mA at 9VDC with a center-negative plug.
- CONTROLS -
FX LVL Knob Controls the output volume of the reverb effect. When
this knob is at the minimum position, the output is only your dry signal.
As the knob is turned up, the reverb output increases in volume. As the
knob is turned past 2 o’clock, the dry signal decreases in volume. When
the knob is at the maximum position, only the effect is output.
TIME Knob Usually controls the decay time of the OCEANS 11 reverb.
As this knob is turned clockwise, the reverb time gets longer and longer,
reaching infinite when the knob is as far as it will go.


Produkt Specifikationer

Mærke: Electro Harmonix
Kategori: Ikke kategoriseret
Model: Oceans 11

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro Harmonix Oceans 11 stil et spørgsmål nedenfor, og andre brugere vil svare dig