EXSYS EX-1083 Manual

EXSYS Netværkskort/adapter EX-1083

Læs gratis den danske manual til EXSYS EX-1083 (2 sider) i kategorien Netværkskort/adapter. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 7 anmeldelser. Har du et spørgsmål om EXSYS EX-1083, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

6 5

Die EX 1083 ist mit 3 externen USB 2.0 Anschlüssen ausgestattet. Der serielle PCI Bus unter-- -

stützt optimal die Leistung des schnellen NEC Chipset. Die USB Karte gewährleistet so eine

sichere Datenübertragung und exzellente Performance von bis zu 480Mbit/s! Die USB 2.0 PCI

Karten sind voll kompatibel mit Microsoft Windows Standard OpenHCD Treibern und sind nach

den Normen des USB Rev. 2.0 entwickelt worden. Sie haben einen Dual Speed USB Transcei-

ver. Sie unterstützen den 32 und 64 bit PCI Bus mit 5 Volt und 3,3 Volt.- - -

ANSCHLÜSSE

BESCHREIBUNG & TECHNISCHE DATEN

AUFBAU

Anleitun

Vers. 1.0 / 06.09.18

E 108

Kompatibilität: PCI 32 bit oder PCI X 64 bit, 33Mhz - - -

Betriebssysteme: Windows ME 2000 XP Vista/ 7/ 8.x/ 10/ Server 20xx/ MAC/ Linux / / /

Anschlüsse: 3x USB 2.0 A Buchse extern -

Lieferumfang: EX 1083, Low Profile Bügel, Anleitung -

Zertifikate:

J1 J3: -3x external USB 2.0 A Port-

J1 J3:-

USB 2.0 Pin‘s

Pin Signal Pin Signal

1 VCC 3 DATA+

2 DATA 4 GND -

Achtung!

Bitte Stecker nie mit

Gewalt oder umgekehrt in

den Anschluss stecken!

HARDWARE INSTALLATION

DRIVER INSTALLATION

If you are ready with the jumper settings, please proceed with the following installation instructions.

Because there are large differences between PC’s, we can give you only a general installation

guide for the card. Please refer your computer’s reference manual whenever in doubt.

1. Turn off the power to your computer and any other connected peripherals.

2. Remove the mounting screws located at the rear and/or sides panels of your Computer and

gently slide the cover off.

3. Locate an available PCI expansion slot and then gently but firmly insert the card. Make sure

that the card is seated and oriented correctly.

4. Then connect the card with a screw to the rear panel of the computer.

5. Gently replace your computer’s cover and the mounting screws.

All OS

After the hardware installation, the operating system will recognize the device automatically and

install the drivers.

CHECK INSTALLED DRIVER

Open the Now you should see at the following new >Device manager< . „USB Controller“ -

entry's:

If you see this or a similar information the device is installed correctly.

NEC Driver (optional)

If you experience any performance problems or if you want to use older operating systems

which doesn't support USB 2.0 such as Windows 98SE. You can download the driver at our

website or you can find the driver on our driver CD. Then you can install the www.exsys.de

optional VIA Drivers as follows. The driver are available up to Vista.

Open and run the file by double click on your mouse and follow the setup pro-“U2v2_1.exe“

gram to finish installation process. After that shut down windows and follow the instructions for

the Hardware installation. After installing the card simply start your computer and the card will

be recognized automatically by your system.

Produkt Specifikationer

Mærke:	EXSYS
Kategori:	Netværkskort/adapter
Model:	EX-1083
Bredde:	120 mm
Højde:	63 mm
Vægt:	150 g
Antal USB 2.0-porte:	3
Understøttede Windows-operativsystemer:	Ja
Værtsgrænseflade:	PCI
Intern:	Ja
Plug and play:	Ja
Output-grænseflade:	USB 2.0
Hot-swap:	Ja
Udvidelseskort formfaktor:	Lavprofil