Futaba SBS-01C Manual

Futaba Radiostyret legetøj SBS-01C

Læs gratis den danske manual til Futaba SBS-01C (2 sider) i kategorien Radiostyret legetøj. Denne vejledning er vurderet som hjælpsom af 64 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 32.5 anmeldelser. Har du et spørgsmål om Futaba SBS-01C, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

SBS-01C

*Solder welding is required for

instruction.

LED Indication

Slot Number Setup

Reset

Function

Specication

Wiring

Every time it's used, current

consumption is added to SBS-01C.

SBS-01C does not reset even if a

connection is removed or it is turned

off.

The consumption capacity returns

to 0. When you'd like to know the

consumption capacity of 1 ight, please

reset before a ight.

*Power supply off isn't done for 5

seconds after a reset. Because data

isn't preserved.

1M23N26733

RX S.BUS2 port

Battery ESC

80mm (3.15 in.)

200mm (7.87 in.)

80mm (3.15 in.)

21mm (0.83in.)

700mm (27.6 in.)

Reset switch LED Voltage cable

Fuse

＜ parts ＞

Heat Shrink Tube

Fuse

To S.BUS2 port of

telemetry receiver

To S.BUS2 of receiver

Current cable

Press the reset switch

　Wiring and connector are not attached.

Use a connector with no electrical power loss.

Use : Current sensor

Detection item：

Current (0A ～ 150A)

Voltage (0V ～ 70V）

Consumption capacity (0mAh ～ 32767mAh）

*Measurement is impossible less than 1A (Current).

Weight 23g（0.81 oz.）：

Voltage : DC 3.7V 7.4V～

Current : 0A 70A～

　　　　70A ～ 150A (within 10 seconds)

Please note that the proper default slot for

this accessory is number 24. This sensor

uses 3 slots, starting at 1, 2, 3, 4, 5, 8, 9,

10, 11, 12, 13, 16, 17, 18, 19, 20, 21, 24,

25, 26, 27, 28, 29. Information on how

to change the slot assignment is included

in the transmitter's manual.

Telemetry current sensor

Instruction Manual

Thank you for purchasing Futaba's

SBS-01C Current Sensor. Please

read this manual thoroughly to

en s u r e pr o p e r c urr e n t s e n s o r

performance. We also encourage

you to retain the manual for future

reference.

WARNING

To utilize the SBS-01C, connect it

to the S.BUS2 port of the Futaba

telemetry enabled receivers.

■ The SBS-01C will not function properly if

connected to an S.BUS port or other channel

ports.

Ensure that the unit is mounted in

an area that will eliminate

exposure to fuel, water and vibration.

■ As with any electronic components, proper

precautions are urged to prolong the life and

increase the performance of the SBS-01C.

Allow a slight amount of slack in

the SBS-01C cables and fasten

them at a suitable location to prevent

any damage from vibration.

Connect the connector polarity

properly.

■ If connected in reverse, explosions or fire

could occur.

Insert the connector securely.

■ If the connector works loose dur ing

model operation, control will be lost and

cause the potential for extreme danger.

Green Normal operation

Red No signal reception

Green/Red When setting up the

slot

Green/Red

Alternate blink Unrecoverable error

● Telemetry data：

The SBS-01C can monitor and display

the in-flight current, voltage, and current

consumption of the drive battery.

●Applicable systems

Futaba T18MZ -WC

Futaba T18MZ V2.6 ～

Futaba T18SZ V1.4 ～

Futaba T4PX V1.4 ～

Can be checked at

the transmitter.

(May, 2016)

● Current

● Voltage

● Consumption capacity

Drive Battery

Battery

The SBS-01C should be mounted

away from magnetic bodies.

■ If close to a magnetic body, the DC current

may not be measured correctly.

Do not install the SBS-01C in a

ammable location.

■ There is danger of ignition and ﬁre.

To ensure that the SBS-01C is

functioning as desired, please test

accordingly.

■ Do not use until inspection is complete.

Be ca re fu l t he b at te r y Lo s t.

■The consumption capacity is indicated.

(It isn't the present battery capacity.)

Don't apply current higher than

rated current to SBS-01C.

■SBS-01C may break down and fall.

Do not use the SBS-01C with

anything other than R/C models.

Never connect current cable

during ＋－ of a battery.

■ There is danger of ignition and ﬁre.

Produkt Specifikationer

Mærke:	Futaba
Kategori:	Radiostyret legetøj
Model:	SBS-01C

Har du brug for hjælp?

Hvis du har brug for hjælp til Futaba SBS-01C stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Radiostyret legetøj Futaba Manualer

Futaba R7208SB Manual

16 Juli 2025

16 Juli 2025

8 Juli 2025

8 Juli 2025

8 Juli 2025

Futaba R7214SB Manual

5 Februar 2025

Futaba GY470 Manual

5 Februar 2025

Futaba GYA553 Manual

5 Februar 2025

Futaba SBS-01RO Manual

15 Januar 2025

Futaba 12Z Manual

3 Oktober 2024

Radiostyret legetøj Manualer

Nyeste Radiostyret legetøj Manualer

FMS A6M5 Zero Manual

1 December 2025

FMS 1:12 Toyota FJ45 Manual

1 December 2025

FMS T-28 Trojan V2 Manual

1 December 2025

FMS 1:24 FCX24 Chevrolet K5 Blazer RTR Manual

1 December 2025

1 December 2025

24 November 2025

23 November 2025

14 November 2025

10 November 2025

Axial SCX30 Ford Bronco Manual

29 Oktober 2025