Heatit Z-TRM3 Manual

Heatit Termostat Z-TRM3

Læs gratis den danske manual til Heatit Z-TRM3 (8 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Heatit Z-TRM3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

1. INTRODUCTION

Heatit Z-TRM3 is an electronic thermostat for electrical ﬂoor heating,

designed to be mounted in a standard ﬂush box. The thermostat has

a built-in Z-Wave chip that can be connected with Home Automation

systems. Heatit Z-TRM3 is equipped with a single-pole relay and ﬁts

into System 55 frames. The thermostat can withstand a load of max

16A /3600W at 230V. The thermostat may be used for water based

heating if the thermostat is linked to the Heatit Z-Water.

NB! If the sensor mode is changed to A or AF mode then a room

sensor compensation process will start, which limits maximum power

output to 75%. The thermostat adapts to the environment within a

few days. No internal sensor calibration should be performed during

the ﬁrst few days.

2. STATEMENT REGARDING PRODUCTS FROM MULTIPLE

MANUFACTURERS

Please read this before installation

This device may be used with all devices certiﬁed with the Z-Wave Plus™

certiﬁcate and should be compatible with such devices produced by

other manufacturers. Every primary controller is diﬀerent depending on

the manufacturer, their target consumer and intended use/application.

Please review the functionalities implemented by the primary controller

you intend to use with our Z-Wave Plus certiﬁed device to ensure that it

provides the necessary controls to take full advantage of our product’s

capabilities.

3. BEHAVIOR WITHIN THE Z-WAVE NETWORK

This device may be operated within any Z-Wave network with

Z-Wave-certiﬁed devices from other manufacturers. All non-battery

operated nodes within the network will act as repeaters regardless of

manufacturer to increase the reliability of the network. On delivery, the

device does not belong to any Z-Wave network. The device needs to be

added to an existing network to communicate with the other devices

within it. Devices may also be removed from a network. The add/remove

processes are initiated by the primary controller of the Z-Wave network.

The primary controller has a mode for adding or removing devices.

Please refer to your primary controller manual on how to set the

primary controller in add/remove mode. The device may only be

added or removed from the network if the primary controller is in

add/remove mode.

4. QUICK START

1. Switch oﬀ the mains supply (disable the fuse).

2. Open the wall switch box.

3. Connect wires according to the labeling described in

chapter 5 ”Installation”.

4. After verifying the connections, switch the mains supply back on.

5. Set the primary controller in add mode (security/non-security).

6. Press and hold the center button until “OFF” is shown on the

display (approx. 10 seconds).

7. Press down button until you reach “CON”, press and hold until the

display shows a rotating light pattern.

8. The thermostat will display “INC” when the thermostat is

successfully added.

NB! If adding/removing fails, Err (error) will appear.

HEATIT

Z-TRM3

Firmware 4.0

Installers manual

Ver 2020-C

TABLE OF CONTENTS

1 Introduction

2 Statement regarding products from multiple manufacturers

3 Behavior within the Z-Wave™ network

4. Quick Start

5. Installation

5.1 Controls

6. Add/Remove

6.1 Method 1 Standard (manual)

6.2 Method 2 SmartStart (automatic)

7 Factory Reset

7.1 Startup

8 Principles of regulation

9 Programming thermostat

10 Temperature shown in display

11 Standby and main screen

12 Choice of sensor

13 Selecting the right Ohm value for your external ﬂoor sensor

14 Calibration

15 Brightness

16 Hysteresis (dIF)

17 Min/Max temperature settings

18 Fast functions from Standby / Main Screen

18.1 Display on/oﬀ - don/doF

18.2 Childlock - Lock

19 Error codes

20 Z-Wave QR-code / DSK

21 Security

22 Node Information Frame

23 Associations

24 Conﬁguration parameters

25 Command class speciﬁcations

Product information

01.03.20

Produkt Specifikationer

Mærke:	Heatit
Kategori:	Termostat
Model:	Z-TRM3
Kode for international beskyttelse (IP):	IP21
Vekselstrømsindgangsspænding:	230 V
Vekselstrømsindgangsfrekvens:	50 - 60 Hz
Produktfarve:	Sort
Strømkilde:	Vekselstrøm
Børnesikring:	Ja
Bæredygtighedscertifikater:	CE, RoHS
Grænseflade:	Z-Wave
Overholdelse af bæredygtighed:	Ja
Måleenhed:	°C
Frekvens:	868.4 MHz
Smart termostat:	Ja
Temperaturføler:	Ja
Velegnet til våde område:	Ingen