Hudson Valley Collins 2938-PN Manual

Hudson Valley Lys Collins 2938-PN

Læs gratis den danske manual til Hudson Valley Collins 2938-PN (1 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Hudson Valley Collins 2938-PN, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
2914,2919,2924,2938
Hudson Valley Lighting, Inc.
P.O. Box 7459
106 Pierces Road
Newburgh, NY 12550
(800) 814- 3993
www.hudsonvalleylighting.com
1. To ensure the success of the fixture installation, the following instructions and
diagram(s) should be read and understood.
2. All electrical connections must be made in accordance with the National Electric
code and local codes and ordinances. If you are uncertain of the methods of
installing electrical wiring and lighting fixtures secure the services of a qualified
licensed electrician.
3. TOOLS NEEDED: Blade screwdriver, phillips screwdriver, slip joint pliers or
small adjustable wrench, wire cutter/stripper, electrical current tester, stepladder
and electrical tape. NOTE: The important safeguards and instructions outlined on
this sheet are not meant to cover all possible conditions and situations that may
occur. It must be understood that common sense, caution and care are factors that
cannot be built into any product. Caution and care must be supplied by the
person(s) installing, operating and maintaining this lighting fixture.
INSTALLATION PREPARATION
1. TURN OFF THE ENTIRE ELECTRICAL CIRCUIT TO WHICH THE LIGHTING
FIXTURE IS TO BE ATTACHED. Move the appropriate circuit breaker to the “off
position or completely remove the fuse controlling the circuit.
2. If an existing fixture is being replaced, remove it and note to which of the wires
in the outlet box the fixture was attached. DO NOT SEPARATE ANY OTHER
WIRES THAT MAY BE IN THE BOX. DO NOT DAMAGE THE INSULATION OF
OLDER WIRING. In regular circumstances the BLACK wire will be the “Hot” lead
and the WHITE wire will be the “Neutral” or “Common” lead. A GREEN or BARE
COPPER wire is the “Ground”. In older buildings it is always good practice to
reconfirm the polarity of the wiring.
3. This fixture is designed to be mounted on a standard round or octagon box. The
box must be securely mounted to the structure of the building.
FIXTURE INSTALLATION
1.Remove the fixture and parts bag(s) from the carton. Before discarding the carton,
double check packing to make certain that all parts are found.
2. Remove the 2 nuts holding the mounting to the fixture.End plate
(Starting at the back), thread the 2 longest mounting screws into the mounting plate
(The green screw is in the front). Attach the mounting plate to the outlet box. (The
green screw should face the floor).
3.Thread the small hex nuts onto the mounting screws. Lock the hex nuts against the
mounting plate.
4.Thread lead ground wire through pipe stem and twist tightly onto body. Keep adding
additional stems required.
5. Thread wire through canopy and carefully slide over stem.
6. Install ball swivel on end of stem.
7.Trim excess wire to min. 6” beyond stem, strip to 5/8” and twist.
8. e canopy up and be sure to align tab with groove in ball swivel.Slid
9 . Fasten the bare copper fixture wire to the green or bare copper wire in the box
or bare copper wire in the box to the crossbar with green screw provided.
NEVER FASTEN THE GROUND WIRE TO THE BLACK OR “HOT” WIRE!
FAILURE TO FOLLOW THIS INSTRUCTION COULD RESULT IN SERIOUS
INJURY OR DEATH!
10. Fasten the white fixture wire to the white wire in the outlet box. Fasten the wires
to together with an approved fastener(wire nut). Starting about 1” b elow the fastener,
tightly wrap connection with the electrical tape so that the tape seals the end of the
fastener. Make sure that there is no exposed wire or strands that could cause a
dangerous short circuit!
11 ack wire in the outlet box. Fasten the. Connect the black fixture wires to the bl
joined wires as in step 10.
12 . Position and mount canopy to outlet box at ceiling with end nuts.
13. Place the shade on the frame.
14 . C. . Install the lamp ( light bulb) NOTE: This fixture is rated for 60 watt type
DO NOT EXCEED RECOMMENDED WATTAGE !
15. Restore power to circuit at breaker or fuse box.

Produkt Specifikationer

Mærke: Hudson Valley
Kategori: Lys
Model: Collins 2938-PN

Har du brug for hjælp?

Hvis du har brug for hjælp til Hudson Valley Collins 2938-PN stil et spørgsmål nedenfor, og andre brugere vil svare dig


Lys Hudson Valley Manualer

Hudson Valley

Hudson Valley Times Square 3806-AGB Manual

30 Juni 2025
Hudson Valley

Hudson Valley Times Square 3810-AGB Manual

30 Juni 2025
Hudson Valley

Hudson Valley Amboy 1504-AGB Manual

29 Juni 2025
Hudson Valley

Hudson Valley Collins 2938-PN Manual

29 Juni 2025
Hudson Valley

Hudson Valley Woodlawn 1728 Manual

28 Juni 2025
Hudson Valley

Hudson Valley Ovid 1920-AGB Manual

27 Juni 2025
Hudson Valley

Hudson Valley Montvale 4813-AGB Manual

4 November 2024
Hudson Valley

Hudson Valley Hollis 3610-AGB Manual

4 November 2024
Hudson Valley

Hudson Valley Highland Falls 9500-AGB Manual

4 November 2024
Hudson Valley

Hudson Valley Preston 4216-HN Manual

4 November 2024

Lys Manualer

Nyeste Lys Manualer

Honeywell

Honeywell HW-T12312 Manual

13 August 2025
V-TAC

V-TAC VT-10176 Manual

13 August 2025
Eurolite

Eurolite LED IP TMH-H420 Manual

13 August 2025
Eurolite

Eurolite LED Silent Par 6 QCL Floor Manual

13 August 2025
Neewer

Neewer FS600C Manual

13 August 2025
Eurolite

Eurolite LED IP PAR 12x8W QCL Manual

13 August 2025
Philips

Philips Ultinon Essential LED 11258UE2X2 Manual

13 August 2025
Plus More

Plus More MO-HF024 Manual

13 August 2025
Philips

Philips Ultinon Essential LED 11362UE2X2 Manual

12 August 2025
Philips

Philips Ultinon Essential LED 11005UE2X2 Manual

12 August 2025