Hudson Valley Woodlawn 1728 Manual

Hudson Valley Lys Woodlawn 1728

Læs gratis den danske manual til Hudson Valley Woodlawn 1728 (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Hudson Valley Woodlawn 1728, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

WOODLAWN

1728

INSTALLATION INSTRUCTIONS

WARNING/CAUTION

·DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS

COMPLETELY BEFORE STARTING INSTALLATION.

·TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL

APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND

MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED

FACTORY TRAINED TECHNICIAN.

·CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH

HANDS AFTER USE.

·REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE

CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE

PRIOR TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.

·DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE

TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT

FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL

ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.

·PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS

www.hvlgroup.com

Questions? We're here to help!

FIXTURE INSTALLATION

1. Attach the MOUNTING PLATE (1) onto the junction box using the MOUNTING SCREWS (2). This fixture is

designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to

the structure of the building.

2. Remove the SCREW COLLAR (3) from the COLLAR LOOP (4). Fully thread the NIPPLE (5) onto the COLLAR

LOOP (4). Thread the HEX NUTS (6) onto the NIPPLE (5) along with TOOTH WASHER (7). Then thread the

NIPPLE (5) unto the MOUNTING PLATE (1). Adjust the NIPPLE (5) so that the threads of the COLLAR LOOP (4)

extends 1/4" beyond the CANOPY (8). Secure using HEX NUT (6).

3. Open the end link the of the CHAIN (9) and attach to the FIXTURE ASSEMBLY (10) at the desired height. Slide the

SCREW COLLAR (3) and the CANOPY (8) onto the CHAIN (9). Attach the other end of the CHAIN (9) unto the

COLLAR LOOP (4). Feed the wires through the CHAIN (9) , SCREW COLLAR (3), CANOPY (8), COLLAR LOOP

(4), NIPPLE (5), and MOUNTING PLATE (1).

4. Cut off excess wires, and strip the insulation off the end of the leads.

5. Attach the Ground wire (Green) to the ground inside the junction box (Generally green or bare copper wire) or the

GROUND SCREW (11) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!

FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

6. Connect the fixture's SPT Neutral (SPT WIRE WITH NO WRITINGS) wire lead to the neutral (Generally white) wire

in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (12). Starting 1" below the

fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener.

MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT

CIRCUIT!

7. Connect the fixture's SPT hot (SPT WITH WRITNGS) wire lead to the hot (Generally black) wire in the junction box.

Fasten the joined wires same as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO

FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

8. Push the wires back into the junction box. Lift up the CANOPY (8) up to the ceiling, and screw the SCREW

COLLAR (3) onto the COLLAR LOOP (4).

9. Screw the BULB (13) up into the SOCKET of the fixture.THIS FIXTURE IS RATED FOR 60 WATT LAMP. DO NOT

EXCEED THE RECOMMENDED WATTAGE!

10. Restore power to the outlet at the breaker or fuse box.

ITEM DESCRIPTION

PART NUMBER

MOUNTING PLATE

HDW-001718

MOUNTING SCREW SCR-001718-M

SCREW COLLAR SCL-001718

COLLAR LOOP LOO-001718

NIPPLE NIP-001718

HEX NUT NUT-001718-H

TOOTH WASHER WAS-001718

CANOPY CPY-001718

CHAIN CHN-001718

FIXTURE ASSEMBLY FAS-001728

GROUND SCREW SCR-001718-G

WIRE NUT NUT-001718-W

BULB

NOT INCLUDED

Produkt Specifikationer

Mærke:	Hudson Valley
Kategori:	Lys
Model:	Woodlawn 1728

Har du brug for hjælp?

Hvis du har brug for hjælp til Hudson Valley Woodlawn 1728 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Hudson Valley Manualer

Hudson Valley Times Square 3806-AGB Manual

30 Juni 2025

Hudson Valley Times Square 3810-AGB Manual

30 Juni 2025

Hudson Valley Amboy 1504-AGB Manual

29 Juni 2025

Hudson Valley Collins 2938-PN Manual

29 Juni 2025

Hudson Valley Woodlawn 1728 Manual

28 Juni 2025

Hudson Valley Ovid 1920-AGB Manual

27 Juni 2025

Hudson Valley Montvale 4813-AGB Manual

4 November 2024

Hudson Valley Hollis 3610-AGB Manual

4 November 2024

Hudson Valley Highland Falls 9500-AGB Manual

4 November 2024

Hudson Valley Preston 4216-HN Manual

4 November 2024

Lys Manualer

Nyeste Lys Manualer

NEO Tools 99-102 Manual

5 December 2025

Ansmann Survival TS3000RF Manual

5 December 2025

Savage Ring Light Beauty Video Kit Manual

5 December 2025

Bosch GLI 18V-3000 Professional Manual

4 December 2025

BakkerElkhuizen EnergyByLight Manual

4 December 2025

Alkalite VBAR 270 Manual

4 December 2025

SPT SL-824T5 Manual

3 December 2025

Aqiila Soundbird B10 Manual

3 December 2025

Savage LED700K Manual

3 December 2025

Sigma HIRO 70 Manual

3 December 2025