Hudson Valley Times Square 3810-AGB Manual

Hudson Valley Lys Times Square 3810-AGB

Læs gratis den danske manual til Hudson Valley Times Square 3810-AGB (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 3 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 2 anmeldelser. Har du et spørgsmål om Hudson Valley Times Square 3810-AGB, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

FIXTURE INSTALLATION

1. Feed the wire through the STEM (6) and twist tightly onto the FIXTURE ASSEMBLY (8). Keep adding additional

stems until you desired hanging height is met.

2. Slide in CANOPY(7) onto the STEM (6), and thread the 1/4 NIPPLE (5) onto the top end of the STEM (6)

3. Pull the wire out from the junction box, and install the MOUNTING PLATE (1) onto the junction box using the

MOUNTING SCREWS (2). This fixture is designed to be mounted on standard round or octagon junction box.

The junction box must be securely mounted to the structure of the building.

4. Trim off the excess wire to a minimum 6" beyond the STEM and strip each wire

5. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the

GROUND SCREW (3) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!

FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!

6. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together

with an approved fastener (WIRE NUT) (4). Starting 1" below the fastener, tightly wrap the connection with

electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED

WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!

7. Connect the black fixture leads to the hot (Generally black) wire in the outlet box. Fasten the joined wires same

as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD

RESULT IN SERIOUS INJURY OR DEATH!

8. Push the wires back into the junction box. Lift up the CANOPY (7) up to the ceiling, and secure it with the

HEADLESS SCREW (10) by using supplied ALLEN KEY TOOLING (9) .

9. Lift the ALABASTER (13) up onto the fixture and secure using the THUMB SCREW (11) .

10. Screw the BULB (12) into the sockets of the fixture.THIS FIXTURE IS RATED FOR 21 WATT LED LAMP. DO

NOT EXCEED THE RECOMMENDED WATTAGE!

11. Restore power to the outlet at the breaker or fuse box.

TIMES SQUARE

3810

INSTALLATION INSTRUCTIONS

WARNING/CAUTION

·DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS

COMPLETELY BEFORE STARTING INSTALLATION.

·TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL

APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND

MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED

FACTORY TRAINED TECHNICIAN.

·CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS

AFTER USE.

·REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE

CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR

TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.

·DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE

TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT

FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL

ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.

·PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS

www.hvlgroup.com

Questions? We're here to help!

ITEM DESCRIPTION PART NUMBER

MOUNTING PLATE HDW-003806

MOUNTING SCREW HDW-003806

GROUND SCREW

HDW-003806

WIRE NUT HDW-003806

1/4 NIPPLE HDW-003806

STEM STM-380603,06,12,18

CANOPY CAS-003806

FIXTURE ASSEMBLY FAS-003810

ALLEN KEY TOOLING HRD-003806

HEADLESS SCREW CAS-003806

THUMB SCREW SCR-003806-T

LED BULB NOT INCLUDED

ALABASTER ALA-003810