I-PRO WV-QJB502-W Manual

I-PRO Ikke kategoriseret WV-QJB502-W

Læs gratis den danske manual til I-PRO WV-QJB502-W (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om I-PRO WV-QJB502-W, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Preface

Mount the camera onto the ceiling or wall using this bracket.

Use this bracket when conduits are used for wiring, or when there is no space

available for wiring in the ceiling or wall.

For the latest information about the supported cameras, refer to our support website

(

https://i-pro.com/global/en/surveillance/training_support/support/technical_information

Specifications

Ambient operating temperature: –50 °C to +60 °C {–58 °F to +140 °F}

Dimensions: ø127 mm × 56.5 mm (H) {ø5 inches × 2-7/32 inches(H)}

Mass: Approx. 470 {1.04 lbs}g

Finish: Aluminum die cast

i-PRO white <WV-QJB502-W>

Light gray <WV-QJB502-G>

Precautions for installation

■ In order to prevent injury, the product must be securely mounted to the wall or ceiling

according to the Installation Guide of the camera.

■ Make sure to remove this product if it will no longer be used.

Standard accessories

Operating Instructions (this manual) .......... 1 pc.

The following parts are used during installation procedures.

Other items that are needed (not included)

• Fixing screw Recommended screw M4/4 or 2 pcs.

Minimum pull-out strength 196 N {44 lbf} (per 1 pc.)

Note:

• Select screws according to the material of the location that the camera will be mounted to.

In this case, wood screws and nails should not be used.

• For information about the minimum pull-out strength, refer to our support website

(https://i-pro.com/global/en/surveillance/training_support/support/technical_information

<Control No.: C0120>)

Attachment plate ......................................1 pc.

Fixing screw for camera

(M4×10 mm {13/32inches}) .................... 4 pcs.

(of them, 1 for spare)

Fixing screw for attachment plate

(M3×10 mm {13/32 inches}) ................... 5 pcs.

(of them, 1 for spare)

Cover ....................................................... 1 pc.

Ns1020-2042

Precautions

■ Do not use this bracket except with suitable cameras.

Failure to observe this may cause a drop resulting in injury or accidents.

■ Do not install this product on a place that is greatly inﬂ uenced by wind.

Installation on a place where the wind speed is 60 m/s {approx. 134 mph} or more may cause

a fall of the product resulting in injury or accidents.

■ Refer installation work to the dealer.

Installation work requires technique and experience. Failure to observe this may cause fire,

electric shock, injury, or damage to the product. Be sure to consult the dealer.

■ Do not rub the edges of metal parts with your hand.

Failure to observe this may cause injury.

When using this product, also read the “Precautions” described in the operating instruc-

tions for the camera to be attached.

Operating Instructions

Included Installation Instructions

Base Bracket

Model No.

WV-QJB502-W

WV-QJB502-G

• Before attempting to connect or install this product, please read these instructions carefully and

save this manual for future use.

• T

he external appearance and other parts shown in this manual may differ from the actual

product within the scope that will not interfere with normal use due to improvement of the

product.

i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting

from failures arising out of improper installation or operation inconsistent with this

documentation.

Preparations

[1] Remove the enclosure from the camera.

Refer to the Installation Guide of the corresponding camera for how to remove the enclosure

from the camera.

[2] Check the installation direction of the conduit and the image

capturing direction of the camera

Check the connection direction of the conduit (direction of the cable access hole for conduit

on this bracket) and the image capturing direction of the camera and then determine the

fixing position of the attachment plate. The fixing position of the attachment plate can be

changed with steps of 90°. The following is an example of the camera direction and the

fixing position of the attachment plate when connecting the conduit from the upper side.

Caution:

• Before attempting to connect or operate

this product, please read these instructions

carefully.

Notice:

• This product is not suitable for use in loca-

tions where children are likely to be present.

• Do not install this product in locations

where ordinary persons can easily reach.

• For information about screws and other

parts required for installation, refer to the

corresponding section of this document.

Camera

Base bracket

⇧TOP mark

Attachment plate

• Align the direction of the attach-

ment plate so that the “ TOP” ⇧

mark of the attachment plate

comes to the upper side.

• Align the direction of the attach-

ment plate so that the “ TOP” ⇧

mark of the attachment plate

comes to the right side.

Note:

• The connection cable is

omitted in the illustration.

Camera

⇧TOP mark

Attachment plate

Base bracket

For U.S. and Canada:

i-PRO Americas Inc.

For Europe and other countries:

i-PRO EMEA B.V.

https://www.i-pro.com/

Parts and functions

Installations

Step1 Make a hole on the installation surface.

Make screw holes or anchor holes in the ceiling or wall, and also cable access hole if [1]

necessary.

No cable access hole is needed when using conduit.

Attachment plate

(accessory)

Fixing screw for

attachment plate

(4pcs.)

(M3×10 mm {13/32

inches}: accessory)

Conduit wiring connector

Cable access hole

Base bracket

Note:

• When mounting to a single-gang junction

box, fix it with screws (2 pcs.) (M4: locally

procured).

• The direction of the attachment plate

(installation direction of the camera) can

be changed with steps of 90° even after

the base bracket is fixed.

83.5 mm × 46 mm

{3-9/32 inches × 1-13/16 inches}/

82.5 mm × 47.6 mm

{3-1/4 inches × 1-7/8 inches}

󱨶

󱨷

83.5 mm {3-9/32 inches}/

83.3 mm {3-9/32 inches}

󱨸

󱨹

63 mm {2-15/32 inches}/

63 mm {2-15/32 inches}

󱨺

Cable access hole

ø25.4 mm {ø1 inch}

Remove the cap for the female thread for the [2]

conduit using a 5 mm {3/16 inches} hexagon

wrench and attach the conduit.

The female thread for conduit is compliant

with ANSI NPSM (parallel pipe threads) 3/4 or

ISO 228-1 (parallel pipe threads) G3/4.

Step2 Fix the base bracket and install the attachment plate and cover in

the direction described in [2] of “Preparations”.

[1] Install the base bracket on the installation surface.

Fixing screws (4 pcs.) (M4: locally procured)

Minimum pull-out strength: 196 N {44 lbf} (per 1 pc.)

[2] Install the attachment plate onto the base bracket and then attach the cover to the

attachment plate. The following is an example when this bracket is installed on the wall.

(Recommended tightening torque: 0.69 N·m {0.51 lbf·ft})

Base bracket

Cap for the female thread for

the conduit

Note:

• When installing this bracket outdoors, be sure to apply waterproofing to the cable access

hole and fixing screw holes.

Cable

Fixing screw (4 pcs.)

(M4: locally procured)

Fixing screw for

attachment plate

(4 pcs.)

(M3×10 mm {13/32

inches}: accessory)

Attachment plate

Base bracket

Step3 Connect the cables to the camera.

Connect an Ethernet cable to the RJ45 network cable from the camera.

Refer to the Installation Guide of the camera for how to install the waterproof connector.

Step4 Fix the camera body to this bracket.

(Recommended tightening torque: 1.37 N·m {1.01 lbf·ft})

Cable

Fixing screw for camera (3 pcs.)

(M4×10 mm {13/32 inches}: accessory)

Cable

Base bracket

Fixing screw for camera (2 pcs.)

(M4×10 mm {13/32 inches}: accessory)

Note:

• When fixing the camera on this bracket, be careful not to pinch the cable with this bracket

and damage the cable sheath.

Step5 Adjust the angle of view of the camera.

Turn on the power of the camera and adjust the angular field of view of the camera.

Refer to the Installation Guide of the corresponding camera for how to connect to a network and

for how to adjust the angle of view of the camera.

Step6 Attach the enclosure.

After finishing the adjustment, attach the enclosure by following the instructions in the Installation

Guide of the corresponding camera.

Refer to the Installation Guide of the corresponding camera for the recommended tightening

torque to be applied when fixing the enclosure of the camera.

Cover

(accessory)

Cover

(accessory)

△

Flat portion

Mark

Produkt Specifikationer

Mærke:	I-PRO
Kategori:	Ikke kategoriseret
Model:	WV-QJB502-W
Type:	Loftmonteringsfod
Antal pr. pakke:	1 stk
Produktfarve:	Hvid

Har du brug for hjælp?

Hvis du har brug for hjælp til I-PRO WV-QJB502-W stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret I-PRO Manualer

I-PRO WV-QJB502-W Manual

12 Marts 2025

I-PRO PWM25AW Manual

20 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Festo DFM-32-100-B-PPV-A-KF Manual

17 Juni 2025

Playtive IAN 285777 Manual

17 Juni 2025

Festo VAEM-L1-S-M3-26 Manual

17 Juni 2025

Festo DFPC-320 Manual

17 Juni 2025

EFX ICAK12 Manual

17 Juni 2025

Bearware 307294 Manual

17 Juni 2025

Futaba MC-9200H/A Manual

17 Juni 2025

Hansgrohe AXOR Montreux 16517800 Manual

17 Juni 2025

OmniMount 2N1-S Manual

17 Juni 2025

Festo DSNU-S-12- -F1A Manual

17 Juni 2025