Klavis Flexshaper Manual


Læs gratis den danske manual til Klavis Flexshaper (13 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 55 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 28 anmeldelser. Har du et spørgsmål om Klavis Flexshaper, eller vil du spørge andre brugere om produktet?

Side 1/13
Flexshaper
Flexshaper
Flexshaper
Flexshaper Flexshaper user manual V1.3 Page of 1 13
F
F
F
FFle
le
le
lelex
x
x
xxs
s
s
ssha
ha
ha
hahap
p
p
ppe
e
e
eer
r
r
rr voltage mapper
CV-controlled voltage mapper and waveshaper
Introduction
The Flexshaper is a highly versatile module when it comes to modify evolving voltages in other
directions and levels. Five settings allow you to fold/expand/clip/compress/invert partially or
completely any or audio signal. The module can act as an envelope-shaping tool, frequency CV
multiplier, waveshaper, clipper, distortion, limiter, curve changer, and more. Five CV inputs offer
limitless control over the placement of the voltage points for dynamic signal sculpting.
Flexshaper
Flexshaper
Flexshaper
FlexshaperFlexshaper
Features at a glance
Process from DC to full audio range
Unipolar/bipolar input mode switch
Nominal & clip level LEDs
Output signal LED
Input gain knob for nominal level setting,
allows clean flat clipping when overdriven
Five manual voltage mapping potentiometers
Five CV control of the voltage mapping points
Simultaneously active unipolar and bipolar outputs
Firmware update via a simple audio file
Compact and skiff-friendly module
Flexshaper
Flexshaper
Flexshaper
Flexshaper Flexshaper user manual V1.3 Page of 2 13
Installation and security
Purpose
This module is meant for installation in a Eurorack-compliant chassis.
It adheres to Eurorack Doepfer mechanical and electrical specifications.
Do not attempt using this module in other mechanical or electrical contexts.
Installation
Before the installation, disconnect the mains power supply from your modular system. Some
power supplies are not safely isolated; there is a risk of injury!
See in the specifications if this module requires 5V from the supply rails. If 5V is needed and your
rack is not providing 5V, do not attempt connection!
Check that the current consumption requirements of this module, when added to your installed
set of modules do not exceed the available current from your supply. This is done by adding up
the current draw of all modules (mA) separately for each of 5V, 12V and -12V rails. (1000mA = 1
amp). If any of these 3 sums exceeds the available current of your supply for that voltage, do not
connect the module to your system; you need a stronger power supply.
The provided supply flat cable can only be inserted in the appropriate orientation at the back of
the module, so there is no risk of error on that end. However, you should pay attention to the
orientation of the cable in the socket of the supply PCB inside your chassis. Cheap sockets
without shrouding may allow you to plug in the connector the wrong way!
The red stripe on the cable should match a stripe printed on the supply board. The stripe also
indicates the -12V side. In case there is no stripe, a -12V marking is a safe indication of the
orientation.
Double check that the connectors are fully inserted and correctly oriented before switching on
the power supply. In case of an anomaly, switch off the power supply immediately and check
everything again.


Produkt Specifikationer

Mærke: Klavis
Kategori: Ikke kategoriseret
Model: Flexshaper

Har du brug for hjælp?

Hvis du har brug for hjælp til Klavis Flexshaper stil et spørgsmål nedenfor, og andre brugere vil svare dig