Klavis ComPair Manual


Læs gratis den danske manual til Klavis ComPair (9 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Klavis ComPair, eller vil du spørge andre brugere om produktet?

Side 1/9
ComPair
ComPair
ComPair
ComPairComPair user manual V1.0 Page of 1 9
ComPair
Dual/window threshold and signal comparator
Overview
The ComPair is a highly versatile while compact module that can handle all kind of voltage
comparison duties in audio, modulation and logic purposes.
Two sections can be used independently or combined as a unified window comparator. Window
comparison goes beyond simple “higher/lower than”, and checks if a signal is within a specific
range.
Besides the usual voltage setting potentiometers, there is an offset input jack on the first section
to allow voltage against voltage comparisons, leading to a 3-signal comparison capability .
A main differentiating feature of the ComPair is the possibility to invert and mute each of the
comparison results on the 3 output jacks. Dedicated LEDs indicate the current status of each
output.
Features
Different usage modes
1. As two independent threshold- -signal comparators to
2. As a single window comparator
3. As a voltage- -voltage comparator to
4. As a 3-signal voltage comparator
For each comparator
o Input and output jacks
o Threshold potentiometer
o Above/Below/Mute 3-position switch
o Signal active LED indication
Window comparison has its dedicated switch and LED
The first comparator has an additional input for signal- -signal to
comparison with offset.
All outputs allow direct Oring by simple shorting via a multiple
Compact module
Aluminium front panel
Compact and skiff-friendly module
ComPair
ComPair
ComPair
ComPairComPair user manual V1.0 Page of 2 9
Installation and security
Purpose
This module is meant for installation in a Eurorack-compliant chassis.
It adheres to Doepfer Eurorack mechanical and electrical specifications.
Do not attempt using this module in other mechanical or electrical contexts.
Installation
Before the installation, disconnect the mains power supply from your modular system.
Some power supplies are not safely isolated; there is a risk of injury!
See in the specifications if this module requires 5V from the supply rails. If 5V is needed and your
rack is not providing 5V, do not attempt connection!
Check that the current consumption requirements of this module, when added to your installed
set of modules do not exceed the available current from your supply. This is done by adding up
the current draw of all modules (mA) separately for each of 5V, 12V and -12V rails. If any of these 3
sums exceeds the available current of your supply for that voltage, do not connect the module to
your system; you need a stronger power supply.
The provided supply flat cable can only be inserted in the appropriate orientation at the back of
the module, so there is no risk of error on that end. However, you should pay attention to the
orientation of the cable in the socket of the supply PCB inside your chassis. Cheap sockets
without shrouding may allow you to plug in the connector the wrong way!
The red stripe on the cable should match a stripe printed on the supply board. The stripe also
indicates the -12V side. In case there is no stripe, a -12V marking is a safe indication of the
orientation.
Double check that the connectors are fully inserted and correctly oriented before switching on
the power supply. In case of an anomaly, switch off the power supply immediately and check
everything again.


Produkt Specifikationer

Mærke: Klavis
Kategori: Ikke kategoriseret
Model: ComPair

Har du brug for hjælp?

Hvis du har brug for hjælp til Klavis ComPair stil et spørgsmål nedenfor, og andre brugere vil svare dig