Klavis Mixwitch Manual


Læs gratis den danske manual til Klavis Mixwitch (11 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Klavis Mixwitch, eller vil du spørge andre brugere om produktet?

Side 1/11
Mixwitch
Mixwitch
Mixwitch
Mixwitch Mixwitch user manual V1.1 Page of 1 11
M
M
M
MMix
ix
ix
ixixw
w
w
wwi
i
i
iitc
tc
tc
tctch
h
h
hh Mixer & Switcher
Voltage & clock-controlled analog switch with mixer
Introduction
Focused versatility seems an oxymoron when describing the features that led us to design the
Mixwitch. With only a pinch of mixing, inverting and controlled switching, we brew up a plethora
of combinations and uses. This is voltage processing magic!
Mixwitch
Mixwitch
Mixwitch
MixwitchMixwitch
Features at a glance
Dual 2 to 1 mixers, normalized into 4 to 1
o C k-less mute per mixer lic
o Click-less polarity inversion per input with LED
indication
o Modulation vs. audio mode selection (lin/log) per
mixer, with change of potentiometer curve response
and LED indication.
o Two LEDs on each output showing the amplitude and
polarity of the output signal
o Unconnected inputs present a xed voltage to ease
oset creation
o Full range -coupled analog signal path DC
Switch /Selector
o Switch among 4 inputs, only 2, or disabled
o Select an input sequentially with a clock/trigger
o Select an input randomly with a clock/trigger
o Select an input in relation to a control voltage
o CV and clock control are audio rate capable
Settings retained over the power cycle
High-quality potentiometers with metal shaft
Ski-friendly compact module &
Mixwitch
Mixwitch
Mixwitch
Mixwitch Mixwitch user manual V1.1 Page of 2 11
Installation and security
Purpose
This module is meant for installation in a Eurorack-compliant chassis.
It adheres to Eurorack Doepfer mechanical and electrical specications.
Do not attempt using this module in other mechanical or electrical contexts.
Installation
Before the installation, disconnect the mains power supply from your modular system. Some
power supplies are not safely isolated; there is a risk of injury!
See in the specications if this module requires 5V from the supply . If 5V is needed and your rails
rack is not providing 5V, do not attempt connection!
Check that the current consumption requirements of this module, when added to your installed
set of modules do not exceed the available current from your supply. This is done by adding up
the current draw of all modules (mA) separately for each of 5V, 12V and -12V rails. If any of these 3
sums exceeds the available current of your supply for that voltage, do not connect the module to
your system; you need a stronger power supply.
The provided supply at cable can only be inserted in the appropriate orientation at the back of
the module, so there is no risk of error on that end. However, you should pay attention to the
orientation of the cable in the socket of the supply PCB inside your chassis. Cheap sockets
without shrouding may allow you to plug in the connector the wrong way!
The red stripe on the cable should match a stripe printed on the supply board. The stripe also
indicates the -12V side. In case there is no stripe, a -12V marking is a safe indication of the
orientation.
Double check that the connectors are fully inserted and correctly oriented before switching on
the power supply. In case of an anomaly, switch o the power supply immediately and check
everything again.


Produkt Specifikationer

Mærke: Klavis
Kategori: Ikke kategoriseret
Model: Mixwitch

Har du brug for hjælp?

Hvis du har brug for hjælp til Klavis Mixwitch stil et spørgsmål nedenfor, og andre brugere vil svare dig