Kramer WP-211T Manual

Kramer Router WP-211T

Læs gratis den danske manual til Kramer WP-211T (4 sider) i kategorien Router. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Kramer WP-211T, eller vil du spørge andre brugere om produktet?

Side 1/4
WP-211T Quick Start
P/N:
2900- 301088QS
Rev:
4
Scan for full manual
WP- Quick Start Guide 211T
This guide helps you install and use your WP-211T for the first time.
Go to www.kramerav.com/downloads/WP-211T to download the latest user manual and check ifrmware
upgrades are available.
Step 1: Check what’s in the box
1 Power adapter and cord
1 Quick start guide
Installation accessories
Step 2: Get to know your - WP 211T
#
Feature
Function
1
INPUT 1
HDMI Connector
Connect to an HDMI source to route to HDBT OUT.
Button
Press momentarily to manually select HDMI 1 (button lights orange).
2
Operation Mode
DIP-switches
By-default the DIP-switches are both set to OFF (left).
Controlling via the INPUT buttons overrides all DIP-switch settings and automatic
switching until the manually selected source disconnects, becomes inactive or WP-211T
is powered o.
DIP-switch 1
OFF (left) - Last connected mode.
ON (right) - Priority mode according to DIP-switch 2 settings.
DIP-Switch 2
OFF (left) - INPUT 1 is the default priority.
ON (right) INPUT 2 is the default priority.
WP-211T DIP-switches are located behind the faceplate and should be set during installation, before placing the
faceplate. Pressing an input button manually selects that input, independent of the DIP-switch settings.
3
INPUT 2
HDMI Connector
Connect to an HDMI Source to route to HDBT OUT.
Button
Press momentarily to manually select HDMI 2 (button lights orange).
4
Grounding Screw
Connect to the common ground (optional) to prevent static electricity from impacting the
performance of the unit.
# Feature Function
5
GND 5V DC 2-pin Terminal
Block Connector
Connect to the supplied power adapter. Not needed on the if there is a PoE WP-211T
provider over HDBaseT.
6
HDBT OUT RJ-45 Connector
Connect to an HDBaseT receiver (for example, TP-580R).
Step 3: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your . For best results, we recommend that you WP-211T
always use Kramer high-performance cables to connect AV equipment to the . WP-211T
Grounding the -211T WP
#
Component Description
1
M3X6 screw
2
1/8" Toothed Lock
Washer
3
M3 Ring Tongue Terminal
To ground the - : WP 211T
1. Connect the ring tongue terminal to the building grounding point wire (it is recommended to use a green-yellow
AWG#18 (0.82mm) wire, crimped with a proper hand-tool).
2. Insert the M3x6 screw through the toothed lock washers and the tongue terminal in the order shown above.
3. Insert the M3x6 screw (with the two toothed lock washers and ring tongue terminal) into the grounding screw hole and
tighten the screw.


Produkt Specifikationer

Mærke: Kramer
Kategori: Router
Model: WP-211T

Har du brug for hjælp?

Hvis du har brug for hjælp til Kramer WP-211T stil et spørgsmål nedenfor, og andre brugere vil svare dig




Router Kramer Manualer

Kramer

Kramer VS-411XS Manual

3 Januar 2025
Kramer

Kramer VS-211X Manual

4 September 2024
Kramer

Kramer WP-211T Manual

31 August 2024
Kramer

Kramer MV-4X Manual

31 August 2024
Kramer

Kramer VS-44H2 Manual

21 August 2024
Kramer

Kramer FC-54P Manual

20 August 2024
Kramer

Kramer VS-42H2 Manual

20 August 2024
Kramer

Kramer FC-7 Manual

19 August 2024
Kramer

Kramer VS-211H2 Manual

17 August 2024
Kramer

Kramer FC-24ETH Manual

17 August 2024

Router Manualer

Nyeste Router Manualer