LiftMaster 380UT Manual

LiftMaster Ikke kategoriseret 380UT

Læs gratis den danske manual til LiftMaster 380UT (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 9 anmeldelser. Har du et spørgsmål om LiftMaster 380UT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Your remote control can be programmed to operate up to two devices, such as a garage door opener, gate

operator, or commercial door operator and has a SMART/ LEARN button. Each button on the remote control

works independently of the other and must be programmed separately. The images throughout this manual are for

reference only and your product may look different.

STOP

Read instructions thoroughly BEFORE beginning. If you are using this product with residential door

openers, this product must be used only with door openers manufactured starting January 1, 1993

that use photoelectric sensors located near the bottom of the door track.

WARNING: This product can expose you to chemicals including lead, which are known to the State of California

to cause cancer or birth defects or other reproductive harm. For more information go to

www.P65Warnings.ca.gov

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

To reduce risk of fire, explosion or chemical burn:

• Replace ONLY with 3V CR2032 coin batteries.

• DO NOT recharge, disassemble, heat above 212°F (100°C) or incinerate.

PROGRAMMING

PROGRAM TO GARAGE DOOR OPENERS WITH A YELLOW LEARN BUTTON

If your remote was previously programmed to another type of opener, see PROGRAM TO COMPATIBLE GARAGE DOOR

OPENERS AND OPERATORS to reprogram to a yellow LEARN button.

1. Start with the garage door closed.

2. Press and immediately release the yellow LEARN button. The Learn LED glows steady for 30 seconds.

Within 30 seconds...

3. Press and hold the button on the remote control you wish to use.

4. Release the button when the garage door opener lights blink or two clicks are heard.

5. Test by pressing the button you just programmed. The opener activates.

To program the remote to Chamberlain accessories, refer to the manual provided with the accessory.

Yellow

LEARN

Button

PROGRAM TO COMPATIBLE GARAGE DOOR OPENERS AND OPERATORS

1. Start with your garage door, gate, or commercial door closed.

2. Remove the remote control cover. Press and hold the program button until the LED turns on.

3. Press and release the SMART/LEARN button on your product or match the remote control DIP SWITCHES

to the existing receiver or existing remote control.

4. Select a button to program on the remote control. Press and release the button the specified number of

times according to the following list. NOTE: Make sure the LED stops flashing between each press of the

button. The garage door opener will respond by clicking, blinking or activating.

... 8 times Chamberlain®* Yellow Button 2011-Current

... 3 times Chamberlain®* Purple Button 2005-Current

... 2 times Chamberlain®* Orange Button 1997-2005

... 4 times Chamberlain®* Green Button 1993-1996

... 6 times Genie Overhead Door®Intellicode 1995-Current

... 5 times Genie Overhead Door®** Intellicode 2005-Current

... 1 time Linear®Mega-Code 1997-Current

... 7 times Stanely®Security Code 1998

... 9 times Wayne Dalton®Rolling Code 372.5 MHz 1999-Current

... 14 times Linear Multicode®10 Position Dip Switch

... 16 times Stanley Multicode®10 Position Dip Switch

... 18 times Linear®8 Position Dip Switch

... 10 times Xtreme Garage®, Guardian®Black Button 2005-Current

... 11 times Sommer®Black Button 1998-Current

* LiftMaster, Do-It, Master Mechanic, Raynor, True Value and Sears Craftsman are

compatible with Chamberlain technology.

** Find Genie Intellicode II instructions at support.chamberlaingroup.com.

5. Press the program button on the remote control to save.

6. Test by pressing the button you just programmed. The opener activates.

To program the remote to Chamberlain accessories, refer to the manual provided with the accessory.

LED

Program

Button

Cover

LEARN

XMITTER

CONTROL BOARD

RADIO

BUTTON

LOGIC BOARD

SMART/LEARN

BUTTON

RECEIVER REMOTEDIP SWITCHES

• The SMART/LEARN button or DIP SWITCHES are located either on the product or in an external receiver on

or near the product. Consult your product owner’s manual to locate the SMART/LEARN button or

DIPSWITCHES.

• If you have a 2 position DIP SWITCH and programming fails, reverse DIP SWITCHES (OFF to ON and

ONtoOFF).

BATTERY

To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

• If battery is swallowed, immediately notify doctor.

To reduce risk of fire, explosion or chemical burn:

• Replace ONLY with 3V CR2032 coin batteries.

• DO NOT recharge, disassemble, heat above 212°F (100°C) or incinerate.

Battery

Dispose of old batteries properly

Replace ONLY with 3V CR2032

coin batteries.

NOTICE: This device complies with part 15 of the FCC rules and Innovation, Science and Economic Development Canada license-exempt

RSSs. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation. Any changes or modifications not

expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules and

Industry Canada ICES standard. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

LiftMaster.com

Chamberlain and LiftMaster are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door Corporation. Overhead Door is a Trademark of Overhead Door Corporation. Linear is a Trademark of Linear Corporation. Master Mechanic is a Trademark of TruServ. Sears is a

Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. Wayne Dalton is a trademark of Wayne Dalton Corporation. Do It is a trademark of Do It Best Corporation. L.L.C. Sommer is a trademark of Sommer Antriebs-und Funktechnik GmbH. Xtreme Garage is a