LumenRadio CRMX Outdoor Flex Manual

LumenRadio Controller CRMX Outdoor Flex

Læs gratis den danske manual til LumenRadio CRMX Outdoor Flex (4 sider) i kategorien Controller. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om LumenRadio CRMX Outdoor Flex, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
RF Link
DMX
RDM
Ethernet
LockPower
RF Link
DMX
RDM
Ethernet
LockPower
CRMX OUTDOOR OPERATION INDICATIONS
When operating, the CRMX Outdoor units show different
indications depending on its mode and link status:
RF Link
DMX
RDM
Ethernet
LockPower
Receiver or repeater when not
linked with a transmitter.
Receiver or repeater
showing a healthy link
with a transmitter.
Receiver or repeater warning
about a link problem.
Transmitter
(regardless of link status)
RF Link
DMX
RDM
Ethernet
LockPower
RF Link
DMX
RDM
Ethernet
LockPower
CRMX OUTDOOR CONTROL PANEL
See the operation section for details on how to
link and unlink CRMX Outdoor units.
Power - on when power applied.
Lock - not used on outdoor
models.
Link button - press to link
with, or unlink from, another
unit.
Status indicators
RF Link on Transmitter:
On = Normal operation.
Fast ashing (~3Hz) = Linking.
Slow ashing (~1Hz) = Unlinking.
RF Link on Receiver/Repeater:
On = Linked with RF signal.
Off = Unlinked.
Fast ashing (~3Hz) = Linking or
linked, but with lost RF signal.
DMX: On when DMX is present.
RDM: Flashes to RDM activity.
Ethernet: Flashes on Ethernet
activity.
Signal quality indicators
Transmitter:
Not used/All off.
Receiver/Repeater:
Top green = 80% signal
quality.
Mid green = 60% signal
quality.
Bottom green = 40%
signal quality.
Amber = 20% signal
quality.
Red = Link problem.
ck Power
RF Link
DMX
RDM
Ethernet
Lock Power
Easy one-button
operation. See
page 2 for details.
Lower indicators
These two indicators remain visible
when the cover is tted to provide
basic status information:
Green indicator: On when linked
and OK.
Red indicator: On if link lost or
unlinked.
CRMX Outdoor
lumenradio
Creating Connectivity for a Better Tomorrow
INTRODUCTION
Thank you for buying a LumenRadio CRMX Outdoor product.
This guide is intended to give you a quick start to experience the
benets of LumenRadio’s CRMX system.
The CRMX products you just purchased are designed to give you
the highest reliability on the market and are fully compatible with
other CRMX products in entertainment lighting (CRMX Nova,
CRMX Outdoor, CRMX Slim, CRMX OEM). Through this you are able
to expand your wireless system with units from our other product
lines as well as with those of our partners. For the latest updates
please visit the LumenRadio website www.lumenradio.com.
We hope that you will enjoy our products and that they will bring
benets and positive experiences.
The information furnished in this start guide is for informational use only and is subject to change without notice. Please check www.lumenradio.com for latest version.
LumenRadio AB assumes no responsibility or liability for any errors or inaccuracies that may appear in this start guide. All information and graphics are property of
LumenRadio AB, Svangatan 2B SE-416 68 Gothenburg, Sweden.
2
Network switch
Computer with SuperNova
CRMX Outdoor uni
t
LINKING
CRMX Outdoor units can link with any other CRMX units as well as legacy W-DMX™ (G2/G3/G4) transmitters (2.4 GHz only).
TO UNLINK
• Unlink one: On the receiver, press
and hold its button for more
than 3 seconds to unlink it from a
transmitter. The RF Link indicator
will extinguish.
• Unlink all: On the transmitter,
press and hold its button for
more than 3 seconds to unlink all
of its receivers.
TO LINK
1. Ensure the antenna is connected.
2. Power on the transmitter and receiver(s).
3. Ensure that the RF Link indicators on all receivers are off to indicate that the
receiver(s) are ready to be linked. (If necessary, follow the unlink procedure.)
4. On the transmitter, press and release the button.
5. The transmitter will search for any unlinked receivers. Its RF Link indicator will ash
for 10 seconds and normal operation will resume.
6. The RF Link indicator will change to a steady on-state on successfully linked
receivers.
MODE CHANGING (CRMX OUTDOOR FLEX ONLY)
Each CRMX Outdoor Flex unit offers the ultimate exibility to operate as either as a transmitter, a receiver or a repeater.
The mode can be changed in either of two ways:
1. Using the SuperNova software. Please refer to the SuperNova website at www.lumenradio.com/supernova for more information.
2. Using a special button press sequence on the CRMX Outdoor Flex unit.
TO CHANGE FLEX MODES
1. Press and release the button ve times in succession. Then immediately press and hold the button for three
seconds until the Lock and Power indicators begin alternately ashing. One of the signal quality indicators will be on:
Green indicator on: Repeater mode selected
Amber indicator on: Receiver mode selected
Red indicator on: Transmitter mode selected
2. You can now change the Flex mode as required. Note that the unit will automatically revert to normal operation fteen sec-
onds after you last pressed the button.
• To step between Flex modes: Press and release the button to move to the next mode.
• To save changes: Press and hold the button for three seconds. The unit will revert to normal operation using the newly
selected mode.
• To exit without saving changes: The unit will revert to normal operation if you do not press the button within fteen sec-
onds.
SUPERNOVA
For conguration, management and monitoring of all CRMX units as well as RDM
compatible devices, LumenRadio provides the software SuperNova free of charge.
SuperNova is needed in order to congure network and port settings, manage
frequency usage, etc.
SuperNova connects to any number of CRMX transmitters through Ethernet. For
best performance, LumenRadio recommends using a network switch and straight
through Ethernet cables. All CRMX units equipped with Ethernet are delivered
with the default network setting on the right:
SuperNova runs on any Windows, Mac OS X or GNU/Linux computer with a Java
runtime environment of at least version 1.6. The latest version of SuperNova as well
as detailed user guides can be accessed at www.lumenradio.com/supernova.
IP Address: 192.168.0.162
Netmask: 255.255.255.0
UNIT FACTORY DEFAULTS

Produkt Specifikationer

Mærke: LumenRadio
Kategori: Controller
Model: CRMX Outdoor Flex

Har du brug for hjælp?

Hvis du har brug for hjælp til LumenRadio CRMX Outdoor Flex stil et spørgsmål nedenfor, og andre brugere vil svare dig


Controller LumenRadio Manualer

LumenRadio

LumenRadio CRMX Outdoor RX Manual

1 September 2024
LumenRadio

LumenRadio CRMX Outdoor Flex Manual

1 September 2024
LumenRadio

LumenRadio CRMX Stardust Manual

1 September 2024
LumenRadio

LumenRadio MoonLite Manual

1 September 2024
LumenRadio

LumenRadio CRMX Slim TX Manual

1 September 2024
LumenRadio

LumenRadio CRMX Luna Manual

1 September 2024
LumenRadio

LumenRadio CRMX Aurora Manual

1 September 2024
LumenRadio

LumenRadio CRMX Slim RX RDM Manual

1 September 2024
LumenRadio

LumenRadio CRMX Galileo TX Manual

1 September 2024

Controller Manualer

Nyeste Controller Manualer

Sonance

Sonance VC60R Manual

2 April 2025
Trust

Trust Mylox GXT 735G Manual

30 Marts 2025
Trust

Trust Mylox GXT 735 Manual

30 Marts 2025
American DJ

American DJ STAGE SETTER-8 Manual

30 Marts 2025
American DJ

American DJ DP-DMX20L Manual

30 Marts 2025
Visual Productions

Visual Productions TimeCore Manual

30 Marts 2025
PCE Instruments

PCE Instruments PCE-RE22T Manual

28 Marts 2025
Turtle Beach

Turtle Beach Recon Manual

27 Marts 2025
AMX

AMX MU-3300 Manual

26 Februar 2025
PowerA

PowerA Enhanced Wireless Controller Manual

26 Februar 2025