Mikrotik BaseBox 6 Manual

Mikrotik Ikke kategoriseret BaseBox 6

Læs gratis den danske manual til Mikrotik BaseBox 6 (7 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Mikrotik BaseBox 6, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/7

10.

BaseBox-series

BaseBox-seriesBaseBox-series

BaseBox 2(RB912UAG-2HPnD-OUT), BaseBox 5(RB912UAG-5HPnD-OUT), BaseBox 6 (RB912UAG-6HPnD-

BaseBox 2(RB912UAG-2HPnD-OUT), BaseBox 5(RB912UAG-5HPnD-OUT), BaseBox 6 (RB912UAG-6HPnD-BaseBox 2(RB912UAG-2HPnD-OUT), BaseBox 5(RB912UAG-5HPnD-OUT), BaseBox 6 (RB912UAG-6HPnD-

This User Manual covers BaseBox models:

This User Manual covers BaseBox models:This User Manual covers BaseBox models:

OUT).

OUT).OUT).

The Basebox is a solid and weatherproof outdoor device based on the RB912 wireless router model. It has high power wireless and one Gigabit Ethernet

connector, which supports MDI-X auto-detection. The device has two RPSMA connectors for connecting external antennas. The device is packaged with a

power adapter, a PoE injector, and two mounting loops. Extra places for more RP-SMA connectors are available on the unit in this case.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This product is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware and configuration or to follow the correct procedures could result in a hazardous situation for people and damage to the system.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

This is a class A device. In a domestic environment, this product might cause radio interference in which case the user might be required to take adequate

measures.

This MikroTik equipment complies with the FCC, IC and European Union radiation exposure limits set forth for an

Exposure to Radio Frequency Radiation:

Exposure to Radio Frequency Radiation:Exposure to Radio Frequency Radiation:

uncontrolled environment.

First use

Choose your powering solution, please see the section for possibilities;Powering

Remove the lid, and connect the antenna to the RP-SMA connectors. Bend the cable with a large radius, so that it will be able to exit through the

cable openings in the bottom of the lid. Put the lid back, with a small arrow to the front of the case;

Open the device's bottom door, to reveal the Ethernet connector;

Connect your direct input power jack if not using POE, to start up the device;

Connect your Ethernet cable to the Gigabit Ethernet port;

Download WinBox configuration tool ;https://mt.lv/winbox

Open WinBox and connect to the device;

Default IP: is not set, user name: , no password, or use

admin

Neighbors tab and connect with MAC address(or, for some models, check user and

wireless passwords on the sticker);

We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best

performance and stability;

Choose your country, apply country regulation settings, and set up your password on the screen that loads.

Mounting

The device can be mounted in several ways: wall, ceiling, pole. To tighten the device to a pole, use the provided metal hose clamp.

Guide the loop around the device through the provided holes, and around the pole where it will be mounted, or use a DIN mount to attach the device to a

rail:

You should avoid connecting a loose Ethernet cable to the Ethernet port, secure the cable to a wall or the pole, so that the cable weight is not pulling the

port. It is recommended to secure the Ethernet cable less than 2m from the device. This is to ensure that the cable doesn't damage the port by its weight,

or doesn't fall out. It is possible to connect grounding wires to the PCB board mounting holes, but to do this, you must remove the PCB from the case.

Powering

The device accepts power from the power jack or from the Ethernet port:

Direct-input power jack (5.5mm outside and 2mm inside, female, pin positive plug) accepts 24 V DC.

Ethernet port accepts passive Power over Ethernet 18-57 V DC (Please compensate voltage for loss due to cable length)

The power consumption under maximum load can reach 12 W. For BaseBox 6 model up to 23 W.

Configuration

RouterOS includes many configuration options in addition to what is described in this document. We suggest

starting here to get yourself accustomed to the possibilities: . In case IP connection is not available,https://mt.lv/help

the Winbox tool ( ) can be used to connect to the MAC address of the device from the LAN sidehttps://mt.lv/winbox

(all access is blocked from the Internet port by default).

For recovery purposes, it is possible to boot the device from the network, see a section .Reset button

Expansion Slots and Ports

BaseBox 2 model - 2.4 GHz, 802.11b/g/n.

BaseBox 5 model - 5 GHz, 802.11a/n.

BaseBox 6 model - 6 GHz, 802.11a/n.

One 10/100/1000 Gigabit Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or

crossover cable for connecting to other network devices.

USB type-A slot.

One miniPCIe slot.

This device might be incompatible with the R11e-LTE international modem.

The miniPCI-e slot usage

Warning! This equipment should be installed and operated with a minimum distance of 380 cm between the device and your body. Operation of

this equipment in the residential environment could cause radio interference.

Produkt Specifikationer

Mærke:	Mikrotik
Kategori:	Ikke kategoriseret
Model:	BaseBox 6

Har du brug for hjælp?

Hvis du har brug for hjælp til Mikrotik BaseBox 6 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Mikrotik Manualer

Mikrotik mANT 15s Manual

3 Januar 2025

Mikrotik CRS320-8P-8B-4S Manual

4 September 2024

Mikrotik LtAP LR8 LTE6 kit Manual

2 September 2024

Mikrotik Woobm-USB Manual

31 August 2024

Mikrotik CME22-2n-BG77 Manual

27 August 2024

Mikrotik hAP ac³ Manual

25 August 2024

Mikrotik L009UiGS-2HaxD-IN Manual

25 August 2024

Mikrotik hAP ax² Manual

25 August 2024

Mikrotik hAP ax³ Manual

25 August 2024

Mikrotik hAP Manual

25 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Racktime Me 2.0 Manual

1 Juli 2025

Ikea SLÅN 302.698.17 Manual

1 Juli 2025

FANAUE CC-06 Manual

1 Juli 2025

Panasonic CS_CU-E9CKP Manual

1 Juli 2025

Ortlieb Quick Rack Light Manual

1 Juli 2025

Cameo DVC D5 Manual

1 Juli 2025

Ikea SÄFFEROT 405.657.23 Manual

1 Juli 2025

Ikea UTRUSTA 802.998.69 Manual

1 Juli 2025

Gigabyte BRIX GB-BRi5H-1335 Manual

1 Juli 2025

DeWalt DW631K Manual

1 Juli 2025