Mikrotik CRS309-1G-8S+IN Manual

Mikrotik Ikke kategoriseret CRS309-1G-8S+IN

Læs gratis den danske manual til Mikrotik CRS309-1G-8S+IN (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 3.5 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Mikrotik CRS309-1G-8S+IN, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

CRS309-1G-8S+IN

CRS309-1G-8S+INCRS309-1G-8S+IN

CRS309-1G-8S+IN

This device is a network switch with eight SFP+ ports and one-gigabit port. It is already configured, with all ports switched together.

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.

This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik devices must be professionally installed.

Quickstart

Mount unit or place on the flat surface, please see paragraph for instructions.

Mounting

Choose your powering solution, please see the section for possibilities.Powering

The Initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility.

Use Winbox to connect to the default IP address of 192.168.88.1 from any port, with the username admin and no password (or, for some models,

, the device is set up as a switch.check user and wireless passwords on the sticker)

Update the device by clicking the "Check for updates" button to v6.46 or the latest RouterOS software to ensure the best performance and

stability. The device needs to have an active internet connection.

For a manual update of the device, visit the products page at to find your product. The required packages are

https://mikrotik.com/products

accessible under the menu;

"Support&Downloads"

Upload downloaded packages to the menu and reboot the device;

WebFigor



Winbox



"Files"

Reboot the device.

By upgrading your RouterOS software to the latest version, you can ensure optimal performance, stability, and security updates;

Set up your password to secure the device.

Mounting

The device is designed to use indoors and it can be mounted in a rackmount enclosure using provided rack mounts, or it can be placed on the desktop.

Please attach rubber pegs on the bottom of the router if the desired placement is on the flat surface or use a Phillips screwdriver to attach rackmount ears

on both sides of the device if designated use is for rackmount enclosure.

Attach rack ears to both sides of the device and tighten four screws to secure them in place, as shown on the picture to the right.

Place the device in a rackmount enclosure and align with the holes so that the device fits conveniently.

Tighten screws to secure it in place.

The IP rating scale for this device is IPX0. The device has no protection from water contamination, please ensure the placement of the device in a dry and

ventilated environment.

We recommend shielded Cat5/6 cables for our devices.

Mounting and configuration of this device should be done by a qualified person.

Powering

The device accepts 11-57 V DC from the direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts. The Ethernet port 1

accepts 802.3af/at and passive PoE power input (18-57 V DC).

The power consumption of this device under maximum load is up to 23 W. It is possible to connect both power inputs at the same time and they will work in

fail-over mode (input with higher voltage will work as the main source).

When using 802.3af/at to power this device, we recommend not using grounding for best compatibility.

Configuration

RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to

the possibilities: .

https://help.mikrotik.com/docs/display/ROS/CRS3xx%2C+CRS5xx%2C+CCR2116%2C+CCR2216+switch+chip+features

In case the IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC address of the device.https://mt.lv/winbox

The device is equipped with an RS-232 serial port, set by default to 115200 bit/s, 8 data bits, 1 stop bit, no parity. For recovery purposes, it is possible to

boot the device for reinstallation, see the next section.

The device supports booting RouterOS (for routing and switching configuration) or SwOS (for only using as a switch). By default, the device will boot

RouterOS, but you can reboot into the other operating system in the following ways:

From SwOS: In the System menu, click the "Boot RouterOS" button on the bottom of the page.

From RouterOS: in the System, RouterBOARD menu, click "Settings" and there select "Boot OS".

It is also possible to select the OS and configure other boot settings via the serial console menu.

Buttons and Jumpers

The reset button has these functions:

Hold this button during boot time until the user LED light starts flashing, release the button to reset RouterOS configuration.

Produkt Specifikationer

Mærke:	Mikrotik
Kategori:	Ikke kategoriseret
Model:	CRS309-1G-8S+IN
Bredde:	141 mm
Dybde:	115 mm
Højde:	28 mm
Produktfarve:	Hvid
Driftstemperatur (T-T):	-40 - 70 °C
Intern hukommelse:	512 MB
Strømforbrug (maks.):	23 W
Netværksstandarder:	IEEE 802.3af, IEEE 802.3at
Udgangsstrøm:	1.2 A
AC-adapter inkluderet:	Ja
Processorfrekvens:	800 MHz
DC indgangsspænding:	12 - 57 V
Flashhukommelse:	16 MB
Strøm over Ethernet (PoE):	Ja
Hukommelsestype:	RAM
Indbygget processer:	Ja
Monteringsbeslag inkluderet:	Ja
Switch-type:	Administreret
10G understøttelse:	Ja
Basis omskiftning RJ-45 Ethernet porte, antal:	1
Basis omskiftning RJ-45 Ethernet porttype:	Gigabit Ethernet (10/100/1000)
Port til konsol:	RS-232
MAC adresselabel:	- entries
Switch kapacitet:	162 Gbit/sek.
Stativ-montering:	Ja
Skruer inkluderet:	Ja
Strømstik:	DC-in-stik
Power over Ethernet (PoE) spændingsområde:	18 - 57 V
Antal SFP + modulslots:	8