Mikrotik CRS310-8G+2S+IN Manual

Mikrotik Ikke kategoriseret CRS310-8G+2S+IN

Læs gratis den danske manual til Mikrotik CRS310-8G+2S+IN (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 70 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 35.5 anmeldelser. Har du et spørgsmål om Mikrotik CRS310-8G+2S+IN, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

CRS310-8G+2S+IN

CRS310-8G+2S+INCRS310-8G+2S+IN

CRS310-8G+2S+IN

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware or to follow the correct procedures could result in a hazardous situation for people and damage to the system.

This product is intended to be installed indoors. Keep this product away from water, fire, humidity, or hot environments.

Use only the power supply and accessories approved by the manufacturer, which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik devices must be professionally installed.

Quickstart

Mount unit or place on the flat surface, please see the paragraph for instructions.Mounting

Choose your powering solution, please see the section for possibilities.Powering

The Initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility.

Use Winbox to connect to the default IP address of 192.168.88.1 from any port, with the username admin and no password (or, for some models,

, the device is set up as a switch.check user and wireless passwords on the sticker)

Update the device by clicking the "Check for updates" button to the latest RouterOS software to ensure the best performance and stability. The

device needs to have an active internet connection.

To manually update the device, go to our download pagehttps://mikrotik.com/download

Choose your architecture (ARM) and download the latest packages from any channel to your PC.

Open Winbox and upload packages in the Files menu.

Reboot the device.

Updating software will ensure the latest security fixes and regulations set by local law.

Choose your Country.

Set up your password to secure the device.

Mounting

The device is designed to use indoors and it can be mounted in a rackmount enclosure using provided rack mounts, or it can be placed on the desktop.

Please attach rubber pegs on the bottom of the router if the desired placement is on the flat surface or use a Phillips screwdriver to attach rackmount ears

on both sides of the device if the designated use is for rackmount enclosure.

Attach rack ears to both sides of the device and tighten four screws to secure them in place, as shown in the picture to the right.

Place the device in a rackmount enclosure and align it with the holes so that the device fits conveniently.

Tighten screws to secure it in place.

The IP rating scale for this device is IP20. The device has no protection from water contamination, please ensure the placement of the device in a dry and

ventilated environment.

We recommend shielded Cat5/6 cables for our devices.

The mounting and configuration of this device should be done by a qualified person.

Powering

The device accepts 18-57 V DC from the direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts. The management

port accepts 802.3af/at and passive PoE power input (18-57 V DC).

The power consumption of this device under maximum load is up to 34 W.

Specifications

Product code CRS310-8G+2S+IN

CPU 98DX226S 800 MHz

CPU architecture ARM 32bit

CPU core count 2

Size of RAM 256 MB

RAM type DDR3

Storage 32 MB, Flash

Number of 2.5G Ethernet ports 8

Number of 10G SFP+ ports 2

Switch chip model 98DX226S

Case dimensions 200 x 206,1 x 44 mm

Dimensions 217,5 x 200 x 47.1 mm

Operating system RouterOS v7, License level 5

Operating temperature -40°C to +60°C

Configuration

Produkt Specifikationer

Mærke:	Mikrotik
Kategori:	Ikke kategoriseret
Model:	CRS310-8G+2S+IN
Kode for international beskyttelse (IP):	IP20
Bredde:	200 mm
Dybde:	206.1 mm
Højde:	44 mm
Produktfarve:	Hvid
Formfaktor:	1U
Driftstemperatur (T-T):	-40 - 60 °C
Intern hukommelse:	256 MB
Operativsystem installeret:	RouterOS
Strømkilde:	DC
Certificering:	CE, EAC, ROHS
Strømforbrug (maks.):	34 W
Processorfrekvens:	800 MHz
DC indgangsspænding:	18 - 57 V
Processormodel:	98DX226S
Flashhukommelse:	32 MB
Strøm over Ethernet (PoE):	Ja
Gennemsnitstid mellem fejl (MTBF):	200000 t
Indbygget processer:	Ja
Switch-type:	Administreret
Switch lag:	L3
10G understøttelse:	Ja
Basis omskiftning RJ-45 Ethernet porte, antal:	8
Basis omskiftning RJ-45 Ethernet porttype:	2.5G Ethernet (100/1000/2500)
MAC adresselabel:	- entries
Switch kapacitet:	- Gbit/sek.
Stativ-montering:	Ja
Antal blæsere:	1 blæser(e)
Strømforsyning inkluderet:	Ja
Antal SFP + modulslots:	2
Antal USB Type-A-porte:	1