Mikrotik CRS326-24G-2S+RM Manual

Mikrotik Ikke kategoriseret CRS326-24G-2S+RM

Læs gratis den danske manual til Mikrotik CRS326-24G-2S+RM (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 92 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 46.5 anmeldelser. Har du et spørgsmål om Mikrotik CRS326-24G-2S+RM, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

CRS326-24G-2S+RM

CRS326-24G-2S+RMCRS326-24G-2S+RM

CRS326-24G-2S+RM

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Ultimate disposal of this product should be handled according to all national laws and regulations.

The Installation of the equipment must comply with local and national electrical codes.

This unit is intended to be installed in the rackmount. Please read the mounting instructions carefully before beginning installation. Failure to use the

correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system.

This product is intended to be installed indoors. Keep this product away from water, fire, humidity or hot environments.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

Read the installation instructions before connecting the system to the power source.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik devices must be professionally installed.

Quick start

Mount unit in a rackmount cabinet or place on the flat surface (see " ").

Mounting

Connect two powering units to the AC source using power cords.

The Initial connection has to be done via the Ethernet cable, using the MikroTik Winbox utility.

Use Winbox to connect to the default IP address of 192.168.88.1 from any port, with the username and no password

admin

(or, for some models,

. If IP is no available choose the Neighbors tab and connect to the device using the MAC check user and wireless passwords on the sticker)

address.

Update the device by clicking the "Check for updates" button to v6.46 or the latest RouterOS software to ensure the best performance and

stability. The device needs to have an active internet connection.

To manually update the device, go to our download pagehttps://mikrotik.com/download

Choose your architecture (ARM) and download the latest packages from any channel to your PC.

Open Winbox and upload packages in the Files menu.

Reboot the device.

Updating software will ensure the latest security fixes and regulations set by local law.

Set up your password to secure the device.

Mounting

The device is designed to use indoors and it can be mounted in a rackmount enclosure using provided rack mounts, or it can be placed on the desktop.

Use a Phillips screwdriver to attach rackmount ears on both sides of the device if designated use is for rackmount enclosure:

Attach rack ears to both sides of the device and tighten four screws to secure them in place, as shown in the picture.

Place the device in a rackmount enclosure and align with the holes so that the device fits conveniently.

Tighten screws to secure it in place.

The device has no protection from water contamination, please ensure the placement of the device in a dry and ventilated environment.

We recommend Cat6 cables for our devices.

Mounting and configuration of this device should be done by a qualified person.

Extension slots and ports

24 of Gigabit Ethernet ports.

Two 10G SFP+ ports.

1x RJ45 console port (set at 115200bits/s, 8 data bits, 1 stop bit no parity).

Please visit wiki pages for MikroTik SFP module compatibility and configuration table: https://wiki.mikrotik.com/wiki

/MikroTik_SFP_module_compatibility_table

Powering

The device accepts power in the following ways:

Ethernet port accepts passive PoE 10-30 V DC .

Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 10-30 V DC.

The power consumption under maximum load can reach 24 W.

Connecting to a PoE Adapter:

Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter;

Connect an Ethernet cable from your local network (LAN) to the PoE adapter;

Connect the power cord to the adapter, and then plug the power cord into a power outlet.

Booting process

The device supports booting RouterOS (for complete routing and switching configuration) or SwOS (for only using as a switch). By default, the device will

boot RouterOS, but you can reboot into the other operating system in the following ways:

From SwOS: In the System menu, click the "Boot RouterOS" button on the bottom of the page.

From RouterOS: in the System, RouterBOARD menu, click "Settings" and there select "Boot OS".

It is also possible to select the OS and configure other boot settings via the serial console menu.

Reset button

The RouterBOOT reset button has the following functions. Press the button and apply the power, then:

Produkt Specifikationer

Mærke:	Mikrotik
Kategori:	Ikke kategoriseret
Model:	CRS326-24G-2S+RM
Bredde:	440 mm
Dybde:	144 mm
Højde:	44 mm
Produktfarve:	Grå
Driftstemperatur (T-T):	-40 - 60 °C
Sikkerhedsalgoritmer:	SNMP
Intern hukommelse:	512 MB
Strømforbrug (maks.):	24 W
Netværksstandarder:	IEEE 802.1Q
Webbaseret administration:	Ja
AC-adapter inkluderet:	Ja
Harmoniseret systemkode (HS):	85176990
Processorfrekvens:	800 MHz
Kompatible operativsystemer:	RouterOS, SwitchOS
Flashhukommelse:	16 MB
Indbygget processer:	Ja
Switch-type:	Administreret
Switch lag:	L2
10G understøttelse:	Ja
Spanning tree protokol:	Ja
VLAN understøttelse:	Ja
Port-spejlning:	Ja
Antal VLAN'er:	4000
Broadcast stormkontrol:	Ja
Basis omskiftning RJ-45 Ethernet porte, antal:	24
Basis omskiftning RJ-45 Ethernet porttype:	Gigabit Ethernet (10/100/1000)
Port til konsol:	RJ-45
Adgangskontrolliste (ACL):	Ja
MAC adresselabel:	- entries
Switch kapacitet:	- Gbit/sek.
Strømforsyning inkluderet:	Ja
Rack monteringskit:	Ja
Antal SFP + modulslots:	2